N285.0-12/N285.6 SERIES-12

Overview In support of Canadian and international industry practices for nuclear power plants, CSA Group has revised this standard to promote best industry practices. This updated standard specifies the technical requirements for the design, procurement, fabrication, installation, modification, repair, replacement, testing, examination and inspection of pressure-retaining systems and containment systems over the service life of a nuclear facility. Changes include clarification of process, piping and designs system rules.

Preface This is the second edition of CSA N285.0/N285.6 Series, General requirements for pressure-retaining systems and components in CANDU nuclear power plants/Material Standards for reactor components for CANDU nuclear power plants. It supersedes the previous edition of the CSA N285.0/N285.6 Series published in 2008, the previous editions of CSA N285.0 published in 2006, 1995, 1991, and 1981, and the previous editions of the CSA N285.6 Series published in 2005 and 1988. CSA N285.0 provides general requirements for pressure-retaining systems, components, and supports in CANDU® nuclear power plants. Note: CANDU (CANada Deuterium Uranium) is a registered trademark of Atomic Energy of Canada Limited (AECL). The CSA N285 series of Standards specifies requirements applicable to nuclear power plants in Canada and references the applicable requirements of the ASME Boiler and Pressure Vessel Code (BPVC). The specific objectives of these Standards are as follows: - to establish technical requirements for pressure boundary items of CANDU power reactors, in a format that regulatory authorities can reference; - to establish requirements for each class of system, component, or support, consistent with the Nuclear Safety and Control Act (Act) and its Regulations; - to reference applicable requirements of the ASME BPVC where they are appropriate to CANDU power reactors; - to specify rules and material requirements for the design, fabrication, installation, quality assurance, and inspection of those pressure-retaining components and supports for which the ASME BPVC does not specify requirements; and - to establish rules for the periodic inspection of pressure-retaining components in CANDU nuclear power plants. The CSA N285 series consists of the following Standards: - CSA N285.0 — General requirements for pressure-retaining systems and components in CANDU nuclear power plants; - CAN/CSA-N285.1 — this Standard no longer exists as a separate publication; it was incorporated into CAN/CSA-N285.0-95; - CAN/CSA-N285.2 — this Standard no longer exists as a separate publication; it was incorporated as Annex I of CSA N285.0-08; - CAN/CSA-N285.3 — this Standard no longer exists as a separate publication; it was incorporated as Annex J of CSA N285.0-08; - CSA N285.4 — Periodic inspection of CANDU nuclear power plant components; - CAN/CSA-N285.5 — Periodic inspection of CANDU Nuclear power plant containment components; - CSA N285.6 Series — Material Standards for reactor components for CANDU nuclear power plants (published with CSA N285.0); and Note: CSA N285.6.5 was withdrawn in the 2005 edition of the CSA N285.6 Series as the material that it covered (heat-treated Zr-2.5Nb-0.5 Cu wire for fuel-channel spacers) is no longer used for new spacers. - CSA N285.8 — Technical requirements for in-service evaluation of zirconium alloy pressure tubes in CANDU reactors. The CSA N-Series Standards provide an interlinked set of requirements for the management of nuclear facilities and activities. The CSA N286 Standard provides overall direction to management to develop and implement sound management practices and controls while the other CSA nuclear Standards provide specific technical requirements and guidance that support the management system. This Standard works in harmony with CSA N286 and does not duplicate the generic requirements of CSA N286; however, it might provide more specific direction for those requirements. Users of this Standard are reminded that the design, fabrication, installation, commissioning, and operation of nuclear facilities in Canada are subject to the provisions of the Act and its Regulations. The Canadian Nuclear Safety Commission (CNSC) specifies regulatory and administrative requirements for pressure-retaining systems in their Regulations and regulatory documents. Where CNSC documents conflict with the requirements of this Standard, the CNSC documents take precedence. In this Standard, the CNSC is referred to as the regulatory authority. The Act and Regulations normally require the following items for a nuclear power reactor: a construction licence, an operating licence, and other licences, certificates, and permits specified by the regulatory authority. These licences and certificates can require the licensee to have the following: - registered designs for systems, components, and supports; - registered welding and brazing procedures; - an accepted overpressure protection report; - accepted code classifications, including applicable standards; - accepted record-keeping systems; - accepted quality assurance programs; and - accepted periodic inspection programs. When a licence references this Standard for another type of nuclear reactor facility, Clause 5 of CSA N285.0 should not be considered relevant unless - the facility has a defined exclusion zone; - access to the facility is controlled, permitting entry only by authorized personnel; and - the reactor is inside a containment structure that is capable of limiting releases to the environment in the event of the failure of a pressure-retaining component. ------------------------------------------------------------------------------- N285.0-12 - General requirements for pressure-retaining systems and components in CANDU nuclear power plants Scope 1.1 This Standard specifies the technical requirements for the design, procurement, fabrication, installation, modification, repair, replacement, testing, examination, and inspection of, and other work related to, pressure-retaining systems, components, and supports over the service life of a CANDU nuclear power plant. 1.2 This Standard applies to all pressure-retaining systems, including their components and supports, in a CANDU nuclear power plant. 1.3 This Standard applies to containment components, but does not apply to concrete containment structures. 1.4 This Standard does not apply to portable assemblies of pressurized items that are temporarily connected to a system or component to enable testing, venting, draining, calibration, or other maintenance activities, provided that they (a) do not reduce the ability of a system to perform its design safety function; (b) are under surveillance when connected and are removed upon completion of their function; and (c) are constructed to Standards deemed by the licensee to be suitable for the application. Note: Safety analysis, environmental qualification programs, or seismic qualification may be used to satisfy the conditions in this Clause. 1.5 In this Standard, \"shall\" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; \"should\" is used to express a recommendation or that which is advised but not required; and \"may\" is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (nonmandatory) to define their application. 1.6 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only. ------------------------------------------------------------------------------- N285.6.1-12 - Pressure tubes for use in CANDU fuel channels Scope This Standard specifies requirements for the fabrication and properties of seamless zirconium-2.5wt % niobium (Zr-2.5Nb) alloy pressure tubes for use in fuel channels in CANDU reactors. ------------------------------------------------------------------------------- N285.6.2-12 - Seamless zirconium alloy tubing for reactivity control units Scope This Standard specifies requirements for the fabrication and properties of seamless zirconium alloy tubing, Grades R60802 and R60804, with diameter to wall thickness ratios less than 80. This tubing is used for reactivity control units in CANDU reactors. ------------------------------------------------------------------------------- N285.6.3-12 - Annealed seamless zirconium alloy tubing for liquid injection shutdown system (LISS) nozzles Scope This Standard specifies requirements for the fabrication and properties of seamless zirconium-tin alloy tubing, Grade R60802 or R60804, which is suitable for use in liquid injection shutdown system (LISS) nozzles located in the moderator water in the core of a CANDU reactor. ------------------------------------------------------------------------------- N285.6.4-12 - Thin-walled, large-diameter zirconium alloy tubing Scope This Standard specifies requirements for the fabrication and properties of thin-walled, large-diameter tubing made from zirconium-tin alloys, Grade R60802 or R60804. Notes: (1) Thin-walled, large diameter tubing has a diameter to wall thickness ratio greater than 50. (2) This tubing can be used as calandria tubes and as tubes for reactivity control units in a CANDU reactor, and may be processed in the seamless or seam-welded condition. ------------------------------------------------------------------------------- N285.6.6-12 - Non-destructive examination criteria for zirconium alloys Scope 1.1 This Standard specifies requirements for non-destructive examinations (NDEs) of zirconium alloy components during manufacturing. NDE methods include visual, radiographic, liquid-penetrant, ultrasonic, and eddy current techniques. 1.2 Other standards may be used for the NDE of zirconium alloys, provided that they satisfy the requirements of this Standard. ------------------------------------------------------------------------------- N285.6.7-12 - Zirconium alloy design data Scope This Standard specifies the physical and mechanical property data to be used in the design of the zirconium alloy components specified in the CSA N285.6 Series. ------------------------------------------------------------------------------- N285.6.8-12 - Martensitic stainless steel for fuel-channel end fittings Scope 1.1 This Standard specifies requirements for martensitic stainless steel forged blanks for the fuel-channel end fittings of a CANDU reactor. ------------------------------------------------------------------------------- N285.6.9-12 - Materials for supports for pressure-retaining items Scope This Standard specifies requirements for material for the support of pressure-retaining items in CANDU nuclear power plants. The materials covered in this Standard are in addition to the materials permitted by the ASME Boiler and Pressure Vessel Code (BPVC), Section III, Division 1, NF-2000, and Code Cases. ------------------------------------------------------------------------------- N285.6.10-12 - Nickel-based alloy wire for fuel-channel spacers Scope This Standard specifies requirements for the nickel-based alloy (UNS N07750) wire used to form spacers for use between the pressure tubes and calandria tubes in the fuel channels in a CANDU reactor. ------------------------------------------------------------------------------- N285.6.11-12 - Zirconium alloy wire Scope This Standard specifies requirements for wires made from zirconium-tin alloy, Grade R60802 or R60804, used in the welding of zirconium components and in the manufacture of the spacers that are installed between pressure tubes and calandria tubes in the fuel channels in a CANDU reactor.