• NBN EN 62282-3-2 : 2007

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    FUEL CELL TECHNOLOGIES - PART 3-2: STATIONARY FUEL CELL POWER SYSTEMS - PERFORMANCE TEST METHODS

    Available format(s): 

    Superseded date:  01-02-2012

    Language(s): 

    Published date:  12-01-2013

    Publisher:  Belgian Standards

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms, definitions and symbols
      3.1 Terms and definitions
      3.2 Symbols
    4 Reference conditions
      4.1 General
      4.2 Temperature and pressure
      4.3 Heating value base
    5 Performance and classes of tests
      5.1 Performance tests
      5.2 Classes of tests
    6 Test preparation
      6.1 General
      6.2 Uncertainty analysis
          6.2.1 Uncertainty analysis items
          6.2.2 Data acquisition plan
    7 Instruments and measurement methods
      7.1 General
      7.2 Instruments
      7.3 Measurement methods
          7.3.1 Electrical power
          7.3.2 Fuel consumption
          7.3.3 Liquid fuel measurements
          7.3.4 Recovered heat
          7.3.5 Purge gas flow
          7.3.6 Oxidant (air) characteristics
          7.3.7 Other fluid flow
          7.3.8 Exhaust gas emission measurement
          7.3.9 Discharge water quality measurement
          7.3.10 pH (Hydrogen ion concentration)
          7.3.11 COD (Chemical Oxygen Demand)
          7.3.12 BOD (Biochemical Oxygen Demand)
          7.3.13 Audible noise level
          7.3.14 Vibration level
          7.3.15 Total harmonic distortion
          7.3.16 Ambient conditions
    8 Test method and computation of results
      8.1 Test plan
          8.1.1 General
          8.1.2 Ambient conditions
          8.1.3 Maximum permissible variation in steady-state
                operating conditions
          8.1.4 Test operating procedure
      8.2 Duration of test and frequency of readings
      8.3 Computation of results
          8.3.1 Electrical power
          8.3.2 Fuel consumption
          8.3.3 Calculation of fuel energy
          8.3.4 Oxidant (air) consumption
          8.3.5 Calculation of oxidant (air) energy
          8.3.6 Electrical efficiency
          8.3.7 Heat recovery efficiency
          8.3.8 Overall energy efficiency
          8.3.9 Power and thermal response characteristics
          8.3.10 Start-up and shutdown characteristics
          8.3.11 Purge gas consumption
          8.3.12 Water consumption
          8.3.13 Waste heat
          8.3.14 Exhaust gas emission
          8.3.15 Calculation of emission production
          8.3.16 Audible noise level
          8.3.17 Vibration level
          8.3.18 Discharge water quality
    9 Test reports
      9.1 General
      9.2 Title page
      9.3 Table of contents
      9.4 Summary report
      9.5 Detailed report
      9.6 Full report
    Annex A (normative) Guidance for uncertainty analysis
    Annex B (normative) Calculation of fuel heating value
    Annex C (normative) Reference gas
    Annex ZA (normative) Normative references to international
              publications with their corresponding European
              publications
    Bibliography

    Abstract - (Show below) - (Hide below)

    Specifies operational and environmental aspects of the stationary fuel cell power systems performance.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher Belgian Standards
    Status Superseded
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective