NEN EN 13852-1 : 2013

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
  5.1 General
  5.2 Structure and mechanisms
      5.2.1 General principles and requirements
      5.2.2 In service loads
      5.2.3 Out of service loads
      5.2.4 Failure mode analysis
      5.2.5 Load combination
  5.3 Equipment and components
      5.3.1 Electrotechnical equipment
      5.3.2 Non-electrotechnical equipment
      5.3.3 Power requirements
      5.3.4 Slewing drives
      5.3.5 Slewing bearings
      5.3.6 Slewing bearing fasteners
      5.3.7 Winches and brakes
      5.3.8 Wire rope termination
      5.3.9 Wire rope anchorage
      5.3.10 Wire ropes
      5.3.11 Hydraulic cylinders
      5.3.12 Motion compensators
      5.3.13 Shock absorbers
  5.4 Drive systems
      5.4.1 General
      5.4.2 Pneumatic systems
      5.4.3 Hydraulic systems
      5.4.4 Electrical systems
      5.4.5 Heave compensation/rope tensioning systems
  5.5 Health and Safety
      5.5.1 Control stations - General
      5.5.2 Control cabin
      5.5.3 Communications
      5.5.4 Noise reduction
      5.5.5 Access
      5.5.6 Guards
  5.6 Controls, indicators and limiting devices
      5.6.1 Controls
      5.6.2 Indicators
      5.6.3 Limiting devices
  5.7 Protection systems
      5.7.1 Overload and over-moment protection
  5.8 Lifting of personnel
      5.8.1 General
      5.8.2 Rated capacity
      5.8.3 Secondary brake
      5.8.4 Cylinders
      5.8.5 Mode selection for personnel lifting
      5.8.6 Personnel rescue
6 Verification of the safety requirements and/or
  protective measures
  6.1 General
  6.2 Testing
      6.2.1 General
      6.2.2 Function test
      6.2.3 Static test
      6.2.4 Installation test
      6.2.5 Test acceptance criteria
      6.2.6 Test load
7 Information for use
  7.1 Documentation
  7.2 Operation
      7.2.1 General
      7.2.2 Checks before starting operation
      7.2.3 Checks during operation
      7.2.4 Crane out of service
      7.2.5 Lifting of personnel (if part of the intended
             use)
  7.3 Maintenance
  7.4 Inspections
  7.5 Marking
      7.5.1 Manufacturer's plate
      7.5.2 Rated capacity information
      7.5.3 Components
Annex A (informative) Selection of a suitable set of
        crane standards for a given application
Annex B (normative) Determination of factors
  B.1 Calculation of the dynamic coefficient phi[n] by
      the simplified method
  B.2 Calculation of dynamic coefficient phi[n] by
      motion response analysis
  B.3 Out of plane
      B.3.1 General
      B.3.2 Offlead load
      B.3.3 Sidelead load
      B.3.4 Horizontal load combination of the
             out-of-plane influences
  B.4 Hook velocity
      B.4.1 Hoisting velocity
      B.4.2 Horizontal hook velocity
  B.5 Load combinations
Annex C (normative) Environmental influences
  C.1 General
  C.2 Wind
      C.2.1 Mean wind velocities
      C.2.2 Boom stalling
  C.3 Floating units
  C.4 Thermal effects
  C.5 Ice
  C.6 Stowage
  C.7 Corrosion protection
Annex D (normative) Failure mode analysis
  D.1 General
  D.2 Failure mode charts
Annex E (normative) Material selection
  E.1 General
  E.2 Verification of material quality
  E.3 Forged rings for slewing bearings
  E.4 Slewing bearing fasteners
  E.5 Welded structures
  E.6 Non-welded components
Annex F (informative) Control station instrumentation
Annex G (normative) Wire rope safety factors
  G.1 General
  G.2 Static safety fact
      G.2.1 Running rigging
      G.2.2 Standing rigging
  G.3 Dynamic safety factors
      G.3.1 Running rigging
      G.3.2 Standing rigging
Annex H (normative) Slewing bearings
Annex I (normative) Requirements for brakes
Annex J (normative) Ranking of safety systems
Annex K (normative) Winches
Annex L (informative) Typical general-purpose offshore
        cranes and terminology
Annex M (informative) Excursion envelope for offlead and
        sidelead
Annex N (normative) Noise test code
  N.1 Introduction
  N.2 Sound power level determination
      N.2.1 Basic standard to be used
      N.2.2 Measurement and calculation procedure
  N.3 Emission sound pressure level determination
      N.3.1 Basic standard to be used
      N.3.2 Crane operator and microphone positions
      N.3.3 Specifications concerning the crane operating
             cabin
      N.3.4 Specification relating to wind speed
      N.3.5 Measurement and calculation procedure
  N.4 Operating conditions
      N.4.1 General
      N.4.2 Test procedure
  N.5 Information on measurement uncertainties
  N.6 Information to be recorded
  N.7 Information to be reported
  N.8 Declaration and verification of noise emission values
  N.9 Noise measurement - Test report
Annex O (normative) Equipment for use in a hazardous area
  O.1 General
  O.2 Avoidance or reduction of ignition sources
  O.3 Electrotechnical equipment
  O.4 Non-electrotechnical equipment
  O.5 Electrostatic discharge
Annex ZA (informative) Relationship between this European
         Standard and the Essential Safety requirements of
         EU Directive 98/37/EC, amended by Directive 98/79/EC

Defines the requirements for general-purpose offshore cranes including their supporting pedestals or structures.