NF EN 1037 : 1996 + A1 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
SAFETY OF MACHINERY - PREVENTION OF UNEXPECTED START-UP
12-01-2013
01-02-2018
Avant-propos
Introduction
1 Domaine d'application
2 Références normatives
3 Définitions
4 Généralités
4.2 Autres mesures destinées à prévenir la mise en
marche intempestive
5 Dispositifs conçus pour la consignation
5.2 Dispositifs de condamnation
5.3 Dispositifs de dissipation ou de retenue [confinement]
de l'énergie accumulée
5.4 Vérification
6 Mesures - autres que la consignation - destinées à éviter
la mise en marche intempestive
6.2 Mesures destinées à empêcher la génération
accidentelle d'ordres de mise en marche
6.3 Mesures destinées à empêcher que des ordres
accidentels de mise en marche ne
provoquent une mise en marche intempestive
6.4 Surveillance automatique de l'arrêt de catégorie 2
Annexe A (informative) Exemples de tâches pouvant
nécessiter la présence de personnes dans
des zones dangereuses
Annexe B (informative) Signalisation, avertissement
Annexe ZA (informative) Relation entre la présente
Norme européenne et les exigences
essentielles de la Directive européenne
98/37/CE
Annexe ZB (informative) Relation entre la présente
Norme européenne et les exigences
essentielles de la Directive européenne
2006/42/CE
Bibliographie
Describes built-in safety measures to prevent unexpected machine start-up to allow safe human interventions in danger zones. Applies to unexpected start-up from all types of energy source.
| DevelopmentNote |
Indice de classement: E09-053-2. Supersedes NFE 09 053. (10/2001) 1996 Edition Re-issued in June 2008 & incorporates AMD 1 2008. (06/2008)
|
| DocumentType |
Standard
|
| PublisherName |
Association Francaise de Normalisation
|
| Status |
Superseded
|
| Supersedes |
| Standards | Relationship |
| EN 1037:1995+A1:2008 | Identical |
| I.S. EN 1037:1996 | Identical |
| UNE-EN 1037:1996 | Identical |
| BS EN 1037 : 1996 | Identical |
| NF EN 15094 : 2008 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR COLD FLAT ROLLING MILLS |
| NF EN 81-43 : 2009 | SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - SPECIAL LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 43: LIFTS FOR CRANES |
| NF EN ISO 11553-1 : 2009 | SAFETY OF MACHINERY - LASER PROCESSING MACHINES - PART 1: GENERAL SAFETY REQUIREMENTS |
| NF EN 14677 : 2008 | SAFETY OF MACHINERY - SECONDARY STEELMAKING - MACHINERY AND EQUIPMENT FOR TREATMENT OF LIQUID STEEL |
| NF EN 14753 : 2008 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR THE CONTINUOUS CASTING OF STEEL |
| NF EN 1114-3 : 2001 + A1 2008 | PLASTICS AND RUBBER MACHINES - EXTRUDERS AND EXTRUSION LINES - PART 3: SAFETY REQUIREMENTS FOR HAUL-OFFS |
| NF EN 528 : 2008 | RAIL DEPENDENT STORAGE AND RETRIEVAL EQUIPMENT - SAFETY REQUIREMENTS |
| NF EN 15164 : 2008 | MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR CHAIN AND BELT SLOTTING MACHINES |
| NF EN 12301 : 2000 + A1 2008 | PLASTICS AND RUBBER MACHINES - CALENDARS - SAFETY REQUIREMENTS |
| NF EN 15061 : 2007 + A1 2009 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR STRIP PROCESSING LINE MACHINERY AND EQUIPMENT |
| NF EN 50308 : 2004 | WIND TURBINES - PROTECTIVE MEASURES - REQUIREMENTS FOR DESIGN, OPERATION AND MAINTENANCE |
| NF EN 15162 : 2008 | MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR GANG SAWS |
| NF EN 15093 : 2008 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR HOT FLAT ROLLING MILLS |
| NF EN 1501-3 : 2008 | REFUSE COLLECTION VEHICLES AND THEIR ASSOCIATED LIFTING DEVICE - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 3: FRONT LOADED REFUSE COLLECTION VEHICLES |
| NF EN 415-8 : 2008 | SAFETY OF PACKAGING MACHINES - PART 8: STRAPPING MACHINES |
| NF EN 12012-1 : 2007 + A1 2008 | PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS |
| NF EN 1218-2 : 2004 + A1 2010 | SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 2: DOUBLE END TENONING AND/OR PROFILING MACHINES FED BY CHAIN OR CHAINS |
| NF EN 692 : 2006 + A1 2009 | MACHINE TOOLS - MECHANICAL PRESSES - SAFETY |
| NF EN 1248 : 2002 + A1 2009 | FOUNDRY MACHINERY - SAFETY REQUIREMENTS FOR ABRASIVE BLASTING EQUIPMENT |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.