NF EN 1555-2 : 2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES
28-09-2021
12-01-2013
Avant-propos
Introduction
1 Domaine d'application
2 Références normatives
3 Termes et définitions, symboles et abréviations
4 Matière
4.1 Composition
4.2 Composition pour les bandes d'identification
5 Caractéristiques générales
5.1 Aspect
5.2 Couleur
6 Caractéristiques géométriques
6.1 Mesurage des dimensions
6.2 Diamètres extérieurs moyens, faux-rond (ovalisation)
et leurs tolérances
6.3 Épaisseurs de paroi et leurs tolérances
6.4 Retrait circonférentiel
7 Caractéristiques mécaniques
7.1 Conditionnement
7.2 Exigences
8 Caractéristiques physiques
8.1 Conditionnement
8.2 Exigences
9 Exigences de performance
10 Marquage
10.1 Généralités
10.2 Marquage minimal exigé
10.3 Marquage supplémentaire
11 Conditions de livraison
Annexe A (informative) Technique d'obturation par écrasement
Bibliographie
Describes the characteristics of pipes made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels. It also specifies the test parameters for the test methods referred to in this standard.
| DevelopmentNote |
Indice de classement: T54-065-2. Supersedes NFT 54 065. (05/2004) PR NF EN 1555-2 March 2009. (03/2009)
|
| DocumentType |
Standard
|
| PublisherName |
Association Francaise de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NS EN 1555-2 : 1ED 2010 | Identical |
| UNE-EN 1555-2:2011 | Identical |
| SN EN 1555-2 : 2010 | Identical |
| EN 1555-2:2010 | Identical |
| DIN EN 1555-2:2010-12 | Identical |
| I.S. EN 1555-2:2010 | Identical |
| UNI EN 1555-2 : 2011 | Identical |
| NBN EN 1555-2 : 2010 | Identical |
| BS EN 1555-2:2010 | Identical |
| NEN EN 1555-2 : 2010 | Identical |
| ONORM EN 1555-2 : 2011 | Identical |
| NFT 54 969 : 2004 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - ELECTROFUSION ANCILLARIES - SAFETY TIME OF THE FUSION CYCLE |
| NFT 54 965 : 2003 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - SPECIFICATIONS FOR THE PACKAGING, THE STORAGE, THE HANDLING AND THE TRANSPORTATION OF THE PIPES |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| EN 1555-1:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| EN 12106:1997 | Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off |
| EN ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| EN ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Small-scale steady-state test (S4 test) (ISO 13477:2008) |
| EN ISO 6259-1:2015 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015) |
| EN ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478:2007) |
| EN ISO 13479:2009 | Polyolefin pipes for the conveyance of fluids - Determination of resistance to crack propagation - Test method for slow crack growth on notched pipes (ISO 13479:2009) |
| EN ISO 13968:2008 | Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility (ISO 13968:2008) |
| EN ISO 9969:2016 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016) |
| EN 1555-5:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
| ISO 13480:1997 | Polyethylene pipes Resistance to slow crack growth Cone test method |
| ISO 6259-3:2015 | Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes |
| EN ISO 2505:2005 | Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005) |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.