• NF EN 60793-1-40 : 2004

    Current The latest, up-to-date edition.

    OPTICAL FIBERS - PART 1-40: MEASUREMENT METHODS AND TEST PROCEDURES - ATTENUATION

    Available format(s): 

    Language(s): 

    Published date:  12-01-2013

    Publisher:  Association Francaise de Normalisation

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    AVANT-PROPOS
    INTRODUCTION
    1 Domaine d'application
    2 Références normatives
    3 Définitions
    4 Conditions d'étalonnage
    5 Méthode d'essai de référence
    6 Appareillage
    7 Echantillonnage et échantillons à l'essai
       7.1 Longueur de l'échantillon à l'essai
       7.2 Face d'extrémité de l'échantillon à l'essai
    8 Procédure
    9 Calculs
       9.1 Méthodes A et B
       9.2 Méthode C
       9.3 Méthode D
    10 Résultats
       10.1 Informations à fournir pour chaque mesure
       10.2 Informations à fournir sur demande
    11 Informations à mentionner dans la spécification
    Annexe A (normative) Prescriptions spécifiques à la méthode
                          A - Fibre coupée
    Figure A.1 - Appareillage de mesure de l'affaiblissement à
                 une longueur d'onde spécifiée
    Figure A.2 - Appareillage de mesure de l'affaiblissement
                 spectral
    Figure A.3 - Montage général d'injection
    Tableau A.1 - Exemples de taille de mandrin
    Tableau A.2 - Conditions d'injection pour les fibres A2 à A4
    Figure A.4 - Montage optique d'injection à limitation spatiale
    Figure A.5 - Système à lentille
    Figure A.6 - Fibre d'injection
    Figure A.7 - Embrouilleur de modes (pour fibre A4)
    Annexe B (normative) Prescriptions spécifiques à la méthode B
                          - Pertes d'insertion
    Figure B.1 - Etalonnage du dispositif de la mesure des pertes
                 d'insertion
    Figure B.2 - Mesure des pertes d'insertion
    Annexe C (normative) Prescriptions spécifiques à la méthode C
                          - Rétrodiffusion
    Figure C.1 - Schéma fonctionnel d'un RODT
    Figure C.2 - Représentation schématique du tracé, sur un RODT,
                 relatif à un échantillon à l'essai 'homogène'
                 précédé d'une fibre amorce
    Figure C.3 - Représentation schématique du tracé, sur un RODT,
                 relatif à un échantillon à l'essai 'homogène' non
                 précédé d'une fibre amorce
    Figure C.4 - Représentation schématique du tracé d'un RODT
                 illustrant des pertes apparentes dues à des
                 discontinuités ponctuelles, l'une réfléchissante,
                 l'autre non réfléchissante
    Figure C.5 - Représentation schématique du tracé agrandi d'un
                 RODT illustrant deux discontinuités ponctuelles,
                 l'une avec un gain apparent et l'autre ne
                 présentant ni perte apparente ni gain apparent
    Annexe D (normative) Prescriptions spécifiques à la méthode D
                          - Modélisation de l'affaiblissement
                          spectral
    Annexe ZA (normative) Références normatives à d'autres
                          publications internationales avec les
                          publications européennes correspondantes

    Abstract - (Show below) - (Hide below)

    Specifies uniform requirements for measuring the attenuation of optical fibres. Four methods are described for measuring attenuation: (a) cut-back, (b) insertion loss, (c) backscattering and (d) modelling spectral attenuation.

    General Product Information - (Show below) - (Hide below)

    Development Note Indice de classement: C93-840-1-40PR. PR NF EN 60793 1-40 January 2000. (02/2002) PR NF EN 60793-1-40 April 2018. (05/2018)
    Document Type Standard
    Publisher Association Francaise de Normalisation
    Status Current

    Standards Referenced By This Book - (Show below) - (Hide below)

    NF EN 60794-1-1 : 2002 OPTICAL FIBER CABLES - PART 1-1: GENERIC SPECIFICATION - GENERAL
    NF EN 60794-2-50 : 2009 OPTICAL FIBRE CABLES - PART 2-50: INDOOR OPTICAL FIBRE CABLES - FAMILY SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES FOR USE IN TERMINATED CABLE ASSEMBLIES
    NF EN 60793-1-45 : 2004 OPTICAL FIBERS - PART 1-45: MEASUREMENT METHODS AND TEST PROCEDURES - MODE FIELD DIAMETER
    NF EN 60794-4-10 : 2007 OPTICAL FIBRE CABLES - PART 4-10: AERIAL OPTICAL CABLES ALONG ELECTRICAL POWER LINES - FAMILY SPECIFICATION FOR OPGW (OPTICAL GROUND WIRES)

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60793-1-43:2015 Optical fibres - Part 1-43: Measurement methods and test procedures - Numerical aperture measurement
    NF EN 60793-1-22 : 2002 OPTICAL FIBERS - PART 1-22: MEASUREMENTS METHODS AND TEST PROCEDURES - LENGTH MEASUREMENT
    NF EN 60793-1-43 : 2002 OPTICAL FIBERS - PART 1-43: MEASUREMENT METHODS AND TEST PROCEDURES - NUMERICAL APERTURE
    IEC 60793-1-22:2001 Optical fibres - Part 1-22: Measurement methods and test procedures - Length measurement
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective