• NF EN 60938-1 : 2008 AMD 1 2008

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION

    Available format(s): 

    Superseded date:  28-09-2021

    Language(s): 

    Published date:  13-01-2013

    Publisher:  Association Francaise de Normalisation

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    AVANT-PROPOS
    1 Généralités
      1.1 Domaine d'application
      1.2 Références normatives
    2 Données techniques
      2.1 Unités et symboles
      2.2 Définitions
      2.3 Valeurs normales
      2.4 Marquage
    3 Procédures d'assurance de la qualité
      3.1 Généralités
      3.2 Stade primaire de fabrication
      3.3 Inductances de structure similaire
      3.4 Procédures d'homologation
      3.5 Controle de la conformité de la qualité
      3.6 Autres méthodes d'essai
      3.7 Paramètres non vérifiés
    4 Mode opératoire d'essai et de mesure
      4.1 Généralités
      4.2 Conditions atmosphériques normales
      4.3 Séchage
      4.4 Examen visuel et vérification des dimensions
      4.5 Résistance d'isolement
      4.6 Tension de tenue
      4.7 Inductance
      4.8 Perte d'insertion
      4.9 Robustesse des connexions de sortie
      4.10 Résistance à la chaleur de soudage
      4.11 Soudabilité (applicable uniquement aux
           connexions de sortie destinées à être
           soudées)
      4.12 Variation rapide de température
      4.13 Vibrations
      4.14 Secousses
      4.15 Chocs
      4.16 Etanchéité du conteneur
      4.17 Séquence climatique
      4.18 Chaleur humide, essai continu
      4.19 Echauffement
      4.20 Endurance
      4.21 Inflammabilité passive
      4.22 Inflammabilité active
      4.23 Résistance du marquage aux solvants
      4.24 Résistance des composants aux solvants
    Annexe A
    Annexe B
    Annexe C

    Abstract - (Show below) - (Hide below)

    Applicable to inductors intended for electromagnetic interference suppression meant to be used in or in association with, electronic or electrical equipment and machines. Restricted to inductors where safety tests are appropriate. Also includes two or more inductors within one enclosure.

    General Product Information - (Show below) - (Hide below)

    Development Note Indice de classement: C93-380-1. PR NF EN 60938-1 Amendment 1, December 2005. (12/2005)
    Document Type Standard
    Publisher Association Francaise de Normalisation
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    NF EN 60938-2 : 2008 AMD 1 2008 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 2: SECTIONAL SPECIFICATION

    Standards Referencing This Book - (Show below) - (Hide below)

    NF EN 60068 2-13 : 1999 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST M: LOW AIR PRESSURE
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    NFC 90 512 : 1983 COMPONENTS FOR ELECTRONIC EQUIPMENT - MEASUREMENT OF THE DIMENSIONS OF ELECTRONIC COMPONENTS
    IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
    IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
    NF EN 60068 2-17 : 1995 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST Q: SEALING
    IECQ 001002-3:2005 IEC QUALITY ASSESSMENT SYSTEM FOR ELECTRONIC COMPONENTS (IECQ) - RULES OF PROCEDURE - PART 3: APPROVAL PROCEDURES
    NF EN 60062 : 2016 MARKING CODES FOR RESISTORS AND CAPACITORS
    IEC 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
    IEC 60068-2-13:1983 Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure
    NF EN 60695 2-2 : 1994 FIRE HAZARD TESTING - PART 2: TEST METHODS - SECTION 2: NEEDLE-FLAME TEST
    NF EN 60068-2-2 : 2007 ENVIRONMENTAL TESTING - PART 2-2: TESTS - TESTS B: DRY HEAT
    NF EN 60068 2-45 : 1993 AMD 1 1994 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST XA AND GUIDANCE: IMMERSION IN CLEANING SOLVENTS
    NF EN 60068 2-29 : 1994 BASIC ENVIRONMENTAL TESTING PROCEDURES - PART 2: TESTS - TEST EB AND GUIDANCE: BUMP
    IEC 60410:1973 Sampling plans and procedures for inspection by attributes
    NF EN 60335-1 : 2013 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS
    IEC 60068-2-3:1969 Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state
    IEC 60294:2012 Measurement of the dimensions of a cylindrical component with axial terminations
    NF EN 60068-2-1 : 2007 ENVIRONMENTAL TESTING - PART 2-1: TESTS - TESTS A: COLD
    IEC 60068-2-17:1994 Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
    NF EN 60068-1 : 2014 ENVIRONMENTAL TESTING - PART 1: GENERAL AND GUIDANCE
    NF EN 60068 2-14 : 2009 ENVIRONMENTAL TESTING - PART 2-14: TESTS - TEST N: CHANGE OF TEMPERATURE
    IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
    NF EN 60068 2-6 : 2008 ENVIRONMENTAL TESTING - PART 2-6: TESTS - TEST FC: VIBRATION (SINUSOIDAL)
    NF EN 60068 2-27 : 2009 ENVIRONMENTAL TESTING - PART 2-27: TESTS - TEST EA AND GUIDANCE: SHOCK
    IEC 60062:2016 Marking codes for resistors and capacitors
    CISPR 17:2011 Methods of measurement of the suppression characteristics of passive EMC filtering devices
    IEC 60068-2-29:1987 Environmental testing. Part 2: Tests. Test Eb and guidance: Bump
    NF EN 60068 2-30 : 2006 ENVIRONMENTAL TESTING - PART 2-30: TESTS - TEST DB AND GUIDANCE: DAMP HEAT, CYCLIC (12 H + 12 H CYCLE)
    IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
    IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
    NF EN 60068-2-21 : 2013 ENVIRONMENTAL TESTING - PART 2-21: TESTS - TEST U: ROBUSTNESS OF TERMINATIONS AND INTEGRAL MOUNTING DEVICES
    IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective