NF ISO 1101 : 2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRICAL TOLERANCING - TOLERANCES OF FORM, ORIENTATION, LOCATION AND RUN-OUT
01-01-2006
12-01-2013
1 Domaine d'application
2 Références normatives
3 Termes et définitions
4 Concepts de base
5 Symboles
6 Cadre de tolérance
7 Éléments tolérances
8 Zones de tolérances
9 Références spécifiées
10 Indications complémentaires
11 Dimensions théoriques exactes (TED)
12 Spécifications restrictives
13 Zone de tolérance projetée
14 Exigence du maximum de matière
15 Exigence du minimum de matière
16 Condition à l'état libre
17 Relation entre tolérances géométriques
18 Définitions des tolérances géométriques
Annexes
A Anciennes pratiques
B Évaluation des écarts géométriques
C Relation avec la matrice GPS
Bibliographie
| DevelopmentNote |
Indice de classement: E04-552. PR NF ISO 1101 Amendment 1, September 2004. (09/2004) Supersedes NFE 04 552. (04/2005)
|
| DocumentType |
Standard
|
| PublisherName |
Association Francaise de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 1101:2017 | Identical |
| NF ISO 15407-2 : 2003 | PNEUMATIC FLUID POWER - FIVE-PORT DIRECTIONAL CONTROL VALVES, SIZES 18 MM AND 26 MM - PART 2: MOUNTING INTERFACES WITH OPTIONAL ELECTRICAL CONNECTOR |
| NF ISO 4401 : 2005 | HYDRAULIC FLUID POWER - FOUR-PORT DIRECTIONAL CONTROL VALVES - MOUNTING SURFACES |
| NF ISO 5599-1 : 2002 | PNEUMATIC FLUID POWER - FIVE-PORT DIRECTIONAL CONTROL VALVES - PART 1: MOUNTING INTERFACES WITHOUT ELECTRICAL CONNECTOR |
| NF ISO 8526-1 : 2006 | MODULAR UNITS FOR MACHINE TOOLS - WORKHOLDING PALLETS - PART 1: WORKHOLDING PALLETS UP TO 800 MM NOMINAL SIZE |
| NF ISO 128-1 : 2003 | TECHNICAL DRAWINGS - GENERAL PRINCIPLES OF PRESENTATION - PART 1: INTRODUCTION AND INDEX |
| NF ISO 15407-1 : 2001 | PNEUMATIC FLUID POWER - FIVE-PORT DIRECTIONAL CONTROL VALVES, SIZES 18 MM AND 26 MM - PART 1: MOUNTING INTERFACE SURFACES WITHOUT ELECTRICAL CONNECTOR |
| NF ISO 4156-3 : 2006 | STRAIGHT CYLINDRICAL INVOLUTE SPLINES - METRIC MODULE, SIDE FIT - PART 3: INSPECTION |
| NF ISO 5599-2 : 2002 AMD 1 2004 | PNEUMATIC FLUID POWER - FIVE-PORT DIRECTIONAL CONTROL VALVES - PART 2: MOUNTING INTERFACE SURFACES WITH OPTIONAL ELECTRICAL CONNECTOR |
| NF ISO 3019-2 : 2002 | HYDRAULIC FLUID POWER - DIMENSIONS AND IDENTIFICATION CODE FOR MOUNTING FLANGES AND SHAFT ENDS OF DISPLACEMENT PUMPS AND MOTORS - PART 2: METRIC SERIES |
| NF ISO 4156-1 : 2006 | STRAIGHT CYLINDRICAL INVOLUTE SPLINES - METRIC MODULE, SIDE FIT - PART 1: GENERALITIES |
| NF EN ISO 12180-1 : 2011 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - CYLINDRICITY - PART 1: VOCABULARY AND PARAMETERS OF CYLINDRICAL FORM |
| NFE 04 561 : 1991 XP | TECHNICAL DRAWINGS - FUNDAMENTAL TOLERANCING PRINCIPLE |
| NF EN ISO 12780-2 : 2011 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - STRAIGHTNESS - PART 2: SPECIFICATION OPERATORS |
| NF EN ISO 1660 : 2017 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRICAL TOLERANCING - PROFILE TOLERANCING |
| NF EN ISO 12781-2 : 2011 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - FLATNESS - PART 2: SPECIFICATION OPERATORS |
| NF EN ISO 12780-1 : 2011 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - STRAIGHTNESS - PART 1: VOCABULARY AND PARAMETERS OF STRAIGHTNESS |
| NF EN ISO 12181-1 : 2011 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ROUNDNESS - PART 1: VOCABULARY AND PARAMETERS OF ROUNDNESS |
| NFE 04 554 : 1988 | TECHNICAL DRAWINGS - DIMENSIONING AND TOLERANCING - DATUMS AND DATUM-SYSTEMS FOR GEOMETRICAL TOLERANCES |
| NF EN ISO 12180-2 : 2011 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - CYLINDRICITY - PART 2: SPECIFICATION OPERATORS |
| NF ISO 128-24 : 2014 | TECHNICAL DRAWINGS - GENERAL PRINCIPLES OF PRESENTATION - PART 24: LINES ON MECHANICAL ENGINEERING DRAWINGS |
| NF EN ISO 12781-1 : 2011 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - FLATNESS - PART 1: VOCABULARY AND PARAMETERS OF FLATNESS |
| NF EN ISO 5458 : 1999 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRICAL TOLERANCING - POSITIONAL TOLERANCING |
| NF ISO 10578 : 1996 | TECHNICAL DRAWINGS - TOLERANCING OF ORIENTATION AND LOCATION - PROJECTED TOLERANCE ZONE |
| NF EN ISO 2692 : 2015 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRICAL TOLERANCING - MAXIMUM MATERIAL REQUIREMENT (MMR), LEAST MATERIAL REQUIREMENT (LMR) AND RECIPROCITY REQUIREMENT (RPR) |
| NF EN ISO 14660-1 : 1999 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRICAL FEATURES - PART 1: GENERAL TERMS AND DEFINITIONS |
| NF ISO/TS 17450-2 : 2004 | GEOMETRICAL PRODUCT SPECIFICATIONS (GSP) - GENERAL CONCEPTS - PART 2: BASIC TENETS, SPECIFICATIONS, OPERATORS AND UNCERTAINTIES |
| NF EN ISO 14660-2 : 1999 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRIC FEATURES - PART 2: EXTRACTED MEDIAN LINE OF A CYLINDER AND A CONE, EXTRACTED MEDIAN SURFACE, LOCAL SIZE OF AN EXTRACTED FEATURE |
| NF ISO 10579 : 2010 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONING AND TOLERANCING - NON-RIGID PARTS |
| NF EN ISO 12181-2 : 2011 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ROUNDNESS - PART 2: SPECIFICATION OPERATORS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.