NF ISO 8015 : 2006

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

TECHNICAL DRAWINGS - FUNDAMENTAL TOLERANCING PRINCIPLE

Available format(s):

Superseded date: 01-08-2011

Language(s):

Published date: 12-01-2013

Publisher: Association Francaise de Normalisation

Abstract - (Show below) - (Hide below)

Le principe spécifié doit être appliqué sur les dessins techniques et les documents connexes aux: - cotes linéaires et à leurs tolérances; - cotes angulaires et à leurs tolérances; - tolérances géométriques;qui définissent, pour chaque élément d'une pièce, les quatre aspects suivants: - dimension; - forme; - orientation; - position.

General Product Information - (Show below) - (Hide below)

Development Note	Indice de classement: E04-561 PR NF ISO 8015 October 2005. (10/2005) Supersedes NFE 04 561 (02/2006)
Document Type	Standard
ISBN
Pages
Published
Publisher	Association Francaise de Normalisation
Status	Superseded
Superseded By	NF EN ISO 8015 : 2011
Supersedes	NFE 04 561 : 1991 XP

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
ISO 8015:2011	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

NF EN 50377-8-13 : 2011	CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-13: TYPE LSH-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY U
NF EN 50377-4-2 : 2011	CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 4-2: TYPE SC/APC SIMPLEX 8 DEGREES TERMINATED ON IEC 60793-2-50 OF TYPES B1.1 AND B1.3 SINGLEMODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
NF ISO 7388-2 : 2007	TOOL SHANKS WITH 7/24 TAPER FOR AUTOMATIC TOOL CHANGERS - PART 2: DIMENSIONS AND DESIGNATION OF SHANKS OF FORMS J, JD AND JF
NF EN 50377-8-11 : 2011	CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-11: TYPE LSH-PC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY C
NF EN 50377-13-2 : 2011	CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 13-2: TYPE LX.5-PC DUPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLE MODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U
NF EN 50377-8-12 : 2011	CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-12: TYPE LSH-APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY U
NF ISO 10110-1 : 2006	OPTICS AND PHOTONICS - PREPARATION OF DRAWINGS FOR OPTICAL ELEMENTS AND SYSTEMS - PART 1: GENERAL
NF EN 50377-8-10 : 2011	CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 8-10: TYPE LSH-APC SIMPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLEMODE FIBRE WITH TITANIUM COMPOSITE FERRULE FOR CATEGORY C
NF EN 50377-13-3 : 2011	CONNECTOR SETS AND INTERCONNECT COMPONENTS TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 13-3: TYPE LX.5-APC DUPLEX TERMINATED ON IEC 60793-2-50 CATEGORY B1.1 AND B1.3 SINGLE MODE FIBRE, WITH FULL ZIRCONIA FERRULE CATEGORY U

Standards Referencing This Book - (Show below) - (Hide below)

ISO 2692:2014	Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
ISO 1101:2017	Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
ISO 286-1:2010	Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart