Foreword
1 Scope
2 Normative references
3 Definitions
3.1 Appliance and its constituent parts
3.2 Adjusting, control and safety devices
3.3 Operation of the appliance
3.4 Gases
3.5 Conditions of operation and measurement
3.6 Classification
4 Construction and design requirements
4.1 General
4.2 Adjusting, control and safety devices
4.3 Ignition devices
4.4 Flame supervision system
4.5 Start-gas flame establishment
4.6 Main flame establishment
4.7 Main burner
4.8 Facility for remote control
4.9 Thermostats and control of air temperature
4.10 Gas pressure test points
5 Operational requirements
5.1 Safety of operation
5.2 Efficiency
6 Test methods
6.1 General
6.2 Construction and design
6.3 Safety of operation
6.4 Efficiency
7 Marking and instructions
7.1 Marking of the appliance
7.2 Marking of the packaging
7.3 Utilization of symbols on the appliance and
packaging
7.4 Instructions
Table 1 - Classification of gases
Table 2 - Valving requirements
Table 3 - Characteristics of the test gases
Table 4 - Calorific values of the test gases of the third
party
Table 5 - Test gases corresponding to the appliance
categories
Table 6 - Test pressures
Table 7 - V[CO2,N], values
Table 8 - Accuracy of measurement
Table 9 - Gas type symbols
Table A.1.1 - Single categories marketed
Table A.1.2 - Double categories marketed
Table A.2 - Normal supply pressures
Table A.3 - Test gas corresponding to categories marketed
nationally or locally
Table A.4
Table A.5 - Inlet connections permitted
Table A.6
Table D.1
Table ZA.1 - Identification form on the compliance of EN 1319
with the essential requirements of the EU
Directive 90/396/EEC on the approximation of the
laws of Member States concerning gas appliances
Figure 1 - Examples of typical valve systems (4.2.8.2)
Figure 2 - Test of an appliance under abnormal draught
conditions (6.3.5.1.4.1, 6.3.6.4.1)
Figure 3 - Test apparatus for type C1 appliances (6.3.5.1.4.3)
Figure 4 - Test apparatus for type C3 appliances - Flat roof
(6.3.5.1.4.4)
Figure 5 - Test apparatus for type C3 appliances - angled roof
(6.3.5.1.4.4)
Figure 6 - C6 test duct system (6.1.6.2.5)
Figure 7 - C6 test duct system - Position of restrictor
(6.1.6.2.5; 6.3.5.2.1)
Figure 8 - C6 test duct system - Detail of restrictor
(6.1.6.2.5)
Figure 9 - C6 test duct system for recirculation test
(6.3.6.4.6.1)
Figure 10 - Positions of sensors for overheat protection
test (6.3.7)
Figure 11 - Test apparatus for combustion products discharge
safety device (type B12BS, B13BS and B14BS
appliances; 6.3.10.4)
Figure 12 - Sampling probe for C6 appliances (6.3.6.2)
Figure 13 - Sampling probe for type B12, B13, B14, C32 and C33
appliances with an outlet diameter of 100 mm or
more (6.4.2)
Figure 14 - Location of the sampling probe for type B12, B13,
B14, C32 and C33 appliances with an outlet
diameter of 100 mm or more (6.4.2)
Figure 15 - Sampling probe for type B12, B13, B14, C32 and
C33 appliances with an outlet diameter of less
than 100 mm (6.4.2)
Figure 16 - Sampling probe for type C12 and C13 appliances
(6.4.2)
Figure 17 - Location of the probe for type C12 and C13
appliances (6.4.2)
Figure 18 - Mean specific heat of dry products of combustion
(6.4.5)
Figure C.1 - Maximum permitted recirculation of the
combustion products
Figure C.2 - Recycling device for pressure loss test (see
C.2.1)
Figure C.3 - Relationship of terminal and wind direction for
wind test (C.2.5)
Annex A (informative) National situations
Annex B (informative) Equivalence rules
Annex C (normative) Requirements and tests for the ducting of
C6 appliances
Annex D (informative) Means of identification of the various
types of gas in force in the various
countries
Annex E (informative) A-deviations
Annex F (normative) Special national conditions
Annex ZA (informative) Clauses of this European Standard
addressing requirements of provisions
of EU Directives