NS EN 14879-4 : 1ED 2007

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 General
  4.1 Materials
      4.1.1 Metallic substrates and semi-finished products
      4.1.2 Linings
  4.2 Selection criteria
      4.2.1 General
      4.2.2 Aggressive substances
      4.2.3 Type and frequency of fluid loading
      4.2.4 Thermal loading
      4.2.5 Changes in temperature
      4.2.6 Mechanical loading
      4.2.7 Climatic influences
      4.2.8 Additional requirements
  4.3 Load profile
  4.4 Design of component
  4.5 Manufacture of the lining
      4.5.1 Environmental conditions
      4.5.2 Surface condition and preparation of the substrate
      4.5.3 Preparation and application of pre-cut parts of the
            semi-finished products
      4.5.4 Lining joints
      4.5.5 Thermal post
  4.6 Lined component
5 Repair of defects
6 Designations
7 Packaging, transport, storage and installation
  7.1 General
  7.2 Packaging and transport
  7.3 Storage
  7.4 Installation
8 External finish of surfaces not to be lined
9 Testing
  9.1 General
  9.2 Basic requirements
      9.2.1 Resistance to the service fluid
      9.2.2 Cleaning and neutralizing processes
      9.2.3 Adhesive strength
      9.2.4 Capability of dissipating electrostatic charges
      9.2.5 Additional requirements
  9.3 Testing of suitability
      9.3.1 General
      9.3.2 Testing of resistance and tightness to the service fluid
      9.3.3 Testing of adhesive strength
      9.3.4 Testing of capability to dissipate electrostatic charges
  9.4 Acceptance inspection
      9.4.1 General
      9.4.2 Visual inspection
      9.4.3 Measurement of lining thickness
      9.4.4 Testing of Hardness
      9.4.5 Testing of Adhesion
      9.4.6 High-voltage testing for tightness
      9.4.7 Testing of capability to dissipate electrostatic
            charges (special test)
      9.4.8 Destructive testing of weld seams (special test)
      9.4.9 Test report
Annex A (informative)
Annex B (normative) Material combinations to which the media
        lists for rubber linings are applicable
 B.1 Hard rubber linings (media list I)
 B.2 Soft rubber lining
     B.2.1 Butyl rubber, halogenated butyl rubber (media list II)
     B.2.2 Chloroprene rubber (media list III)
 B.3 Test media for the media lists
     B.3.1 General
     B.3.2 Media lists
Annex C (normative) Test fluid groups for verification of
        suitability for material/media combinations
Annex D (normative) Testing the dissipating capability
 D.1 Principle
     D.1.1 Dissipation resistance
     D.1.2 Dissipation resistance to earth
 D.2 Testing of dissipation resistance of test samples
     D.2.1 Test equipment
     D.2.2 Test procedure
     D.2.3 Test report
 D.3 Measurement of dissipation resistance to earth on the
     completely applied lining
     D.3.1 Test equipment
     D.3.2 Preparation of the lining
     D.3.3 Procedure
     D.3.4 Test report
Annex E (informative) Sample form for acceptance inspection report
Annex F (informative) A-deviations
Bibliography

Defines the requirements for and methods of testing of organic linings which are applied to metallic process engineering equipment that will come in contact with chemical substances.