Skip to content
Please enter a keyword to search

  • ONORM EN 12201-3 : 2013

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS

    Available format(s): 

    Superseded date:  25-07-2023

    Language(s): 

    Published date:  12-01-2013

    Publisher:  Osterreichisches Normungsinstitut/Austrian Standards

    Sorry this product is not available in your region.

    Add To Cart

    Abstract - (Show below) - (Hide below)

    In dieser ÖNORM werden die Anforderungen an Formstücke aus Polyethylen (PE) festgelegt, die für die Versorgung mit Wasser für den menschlichen Gebrauch sowie die Fortleitung von Rohwasser, das zur Aufbereitung zu Trinkwasser verwendet wird, eingesetzt werden. Weiters werden auch die Prüfparameter für die Prüfverfahren festgelegt, auf die in dieser Norm verwiesen wird. Zusammen mit den übrigen Teilen der EN 12201 gilt dieser Teil für Formstücke aus PE, deren Verbindungen untereinander und mit anderen Rohrleitungsteilen aus PE sowie mit Rohrleitungsteilen aus anderen Werkstoffen, die zur Verwendung unter den folgenden Bedingungen vorgesehen sind: a) der maximal zulässige Betriebsdruck MOP beträgt nicht mehr als 25 bar (1 bar = 105 N/m2); b) es gilt eine Betriebstemperatur von 20 grad C als Bezugstemperatur. Diese Norm ist für die folgenden Arten von Formstücken anwendbar: - Schweissverbindungen - Formstücke für Heizelement- Stumpfschweissung; - Formstücke für Heizelement- Muffenschweissung; - Formstücke für Heizwendelschweissung; - Mechanische Verbindungen; - Klemmverbinder; - Flanschverbindungen; - Flansche; - Bunde.

    General Product Information - (Show below) - (Hide below)

    Committee TC 005
    Development Note Supersedes ONORM EN 13244-3. (03/2012)
    Document Type Standard
    Publisher Osterreichisches Normungsinstitut/Austrian Standards
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    ONORM EN 12201-1 : 2015 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 1: GENERAL
    ONORM EN 12201-4 : 2012 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 4: VALVES

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
    ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
    ISO 13956:2010 Plastics pipes and fittings Decohesion test of polyethylene (PE) saddle fusion joints Evaluation of ductility of fusion joint interface by tear test
    ONORM EN 12201-2 : 2013 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 2: PIPES
    ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
    ISO 12176-1:2017 Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion
    ONORM EN 12201-1 : 2015 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 1: GENERAL
    CEN/TR 15438:2007 Plastics piping systems - Guidance for coding of products and their intended uses
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 14236:2000 Plastics pipes and fittings Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems
    ISO 1167-3:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components
    ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
    ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
    ISO 11357-6:2008 Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
    ONORM EN ISO 1133-1 : 2012 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS - PART 1: STANDARD METHOD (ISO 1133-1:2011)
    ISO 9624:1997 Thermoplastics pipes for fluids under pressure Mating dimensions of flange adapters and loose backing flanges
    ISO 1133-2:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
    ISO 13950:2007 Plastics pipes and fittings Automatic recognition systems for electrofusion joints
    ISO 13951:2015 Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective