Skip to content
Please enter a keyword to search

  • ONORM EN 1555-5 : 2011

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM

    Available format(s): 

    Superseded date:  07-01-2022

    Language(s): 

    Published date:  12-01-2013

    Publisher:  Osterreichisches Normungsinstitut/Austrian Standards

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Fitness for purpose
      4.1 Method of preparation of assemblies for testing
          4.1.1 General
          4.1.2 Butt fusion joints
          4.1.3 Electrofusion jointing
          4.1.4 Mechanical joints
      4.2 Requirements for fitness for purpose
          4.2.1 Fitness for purpose for butt fusion joints
          4.2.2 Fitness for purpose for electrofusion joints
          4.2.3 Fitness for purpose for mechanical joints
    5 Overall service (design) coefficient
    Annex A (informative) Derating coefficients for operating
            temperatures
    Annex B (informative) Rapid crack propagation (RCP) resistance
            at temperature less than 0 degree C
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes requirements of fitness for purpose of the polyethylene (PE) piping system in the field of the supply of gaseous fuels. It also provides the definitions of electrofusion, butt fusion and mechanical joints.

    General Product Information - (Show below) - (Hide below)

    Committee TC 005
    Development Note Supersedes ONORM B 5192. (01/2005)
    Document Type Standard
    Publisher Osterreichisches Normungsinstitut/Austrian Standards
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    ONORM EN 1555-3 : 2013 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 3: FITTINGS
    ONORM EN 15001-1 : 2011 GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING
    ONORM EN 1555-4 : 2011 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 4: VALVES
    ONORM EN 1555-1 : 2015 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL
    ONORM EN 1555-2 : 2011 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
    ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
    ISO 10838-3:2001 Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm
    ONORM EN 1555-2 : 2011 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES
    ISO 10838-2:2000 Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm
    ISO 10838-1:2000 Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
    ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
    ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)
    ONORM EN 1555-3 : 2013 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 3: FITTINGS
    ONORM EN 1555-1 : 2015 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL
    ISO 13478:2007 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST)
    ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
    ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective