Skip to content
Please enter a keyword to search

  • DIN EN 1555-5:2010-12

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system

    Available format(s):  Hardcopy, PDF

    Superseded date:  28-01-2022

    Language(s):  English, German

    Published date:  01-12-2010

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN HDBK 190 : 3ED 2006 ROHRE, ROHRLEITUNGSTEILE UND ROHRVERBINDUNGEN AUS THERMOPLASTISCHEN KUNSTSTOFFEN

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 1555-1:2010 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
    EN 1555-3:2010+A1:2012 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
    ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
    ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
    ISO 10838-3:2001 Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm
    ISO 13956:2010 Plastics pipes and fittings Decohesion test of polyethylene (PE) saddle fusion joints Evaluation of ductility of fusion joint interface by tear test
    EN ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006)
    ISO 10838-2:2000 Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm
    EN ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
    ISO 10838-1:2000 Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
    ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
    ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)
    EN ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Small-scale steady-state test (S4 test) (ISO 13477:2008)
    EN ISO 13478:2007 Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478:2007)
    ISO 11414:2009 Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
    ISO 13478:2007 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST)
    EN ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007)
    ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
    PREN 1555-4 : DRAFT 2008 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 4: VALVES
    ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
    EN 12007-2:2012 Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar)
    EN 1555-2:2010 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes
    CEN/TS 1555-7:2013 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
    ISO 11413:2008 Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective