ONORM EN ISO 13503-3 : 2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PETROLEUM AND NATURAL GAS INDUSTRIES - COMPLETION FLUIDS AND MATERIALS - PART 3: TESTING OF HEAVY BRINES
15-10-2022
12-01-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
3.1 Terms and definitions
3.2 Symbols and abbreviated terms
4 Requirements
4.1 Quality control instructions
4.2 Records retention
5 Calibration of equipment
5.1 General requirements
5.2 Reagents and materials for calibration
5.3 General requirements for calibration of particular
apparatus
5.4 Frequency of calibration verification
5.5 Calibration verification
6 Density
6.1 General
6.2 Apparatus
6.3 Density measurement by hydrometer
6.4 Density correction to 21 degree C (70 degree F)
6.5 Calculation of density in units other than kg/m[3]
6.6 Calculation for pressure and temperature compensation
7 Crystallization temperature
7.1 Principle
7.2 Apparatus
7.3 Determination of crystallization point
7.4 Calculation of crystallization point
8 Brine clarity
8.1 Principle
8.2 Apparatus
8.3 Determination of brine clarity
9 Solids evaluation by gravimetric procedures
9.1 Principle
9.2 Apparatus
9.3 Preparation of glass-fibre filter disk
9.4 Selection of sample volume
9.5 Determination of total suspended solids
9.6 Calculation of total suspended solids
9.7 Calculation of precision and bias
9.8 Determination of volatile and non-volatile solids
9.9 Calculation of non-volatile and volatile solids
10 pH
10.1 Principle
10.2 Reagents and materials
10.3 Apparatus
10.4 Measurement of pH
10.5 Precision statement
10.6 Care of the electrode
11 Iron contamination
11.1 Principle
11.2 Reagents and materials
11.3 Apparatus
11.4 Preparation of colorimetric standards
11.5 Measurement of iron contamination
11.6 Precision statement
12 Daily completion fluid report
12.1 Principle
12.2 Well identification, geometry and zone data
12.3 System properties
12.4 Fluids accounting
12.5 Cost accounting
12.6 Daily commentary
12.7 Vendor representative identification
Annex A (informative) Completion fluids report form
Annex B (informative) Gas hydrates
Annex C (informative) Buffering capacity of brines
Annex D (informative) Pressure crystallization of brines
Annex E (informative) Brine viscosity
Annex F (informative) Principle of corrosion testing
Bibliography
Covers the physical properties, potential contaminants and test procedures for heavy brine fluids manufactured for use in oil and gas well drilling, completion and workover fluids.
DocumentType |
Standard
|
PublisherName |
Osterreichisches Normungsinstitut/Austrian Standards
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
I.S. EN ISO 13503-3:2006 | Identical |
SN EN ISO 13503-3 : 2006 CORR 2007 | Identical |
UNI EN ISO 13503-3 : 2006 | Identical |
BS EN ISO 13503-3:2005 | Identical |
NF EN ISO 13503-3 : 2006 | Identical |
DIN EN ISO 13503-3:2006-05 | Identical |
ISO 13503-3:2005 | Identical |
NBN EN ISO 13503-3 : 2006 COR 2007 | Identical |
NEN EN ISO 13503-3 : 2006 C1 2007 | Identical |
NS EN ISO 13503-3 : 2005 AC 2007 | Identical |
ISO 10414-1:2008 | Petroleum and natural gas industries — Field testing of drilling fluids — Part 1: Water-based fluids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.