PD IEC/TR 63054:2017
Current
The latest, up-to-date edition.
Low-voltage switchgear and controlgear. Fire risk analysis and risk reduction measures
Hardcopy , PDF
English
04-09-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Ignition modes for electrical fires
5 Conclusion
Bibliography
Pertains to the fire risk analysis of low-voltage switchgear and controlgear (hereinafter referred to as 'equipment') referring to the IEC 60947 relevant publications, where the following applies: - only the case where a fire originates (typically under fault or misuse conditions) within the equipment; - only equipment installed in normal environments. Hazardous environments, for example in presence of combustible materials, is not to be considered; - only the case of products selected, installed and used according to the manufacturer instructions and installation rules.
| Committee |
PEL/121/1
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
This document applies to the fire risk analysis of low-voltage switchgear and controlgear (hereinafter referred to as \'equipment\') referring to the IEC 60947 relevant publications, where the following applies:
only the case where a fire originates (typically under fault or misuse conditions) within the equipment;
only equipment installed in normal environments. Hazardous environments, for example in presence of combustible materials, is not to be considered;
only the case of products selected, installed and used according to the manufacturer instructions and installation rules.
In addition, the following cases are not considered:
faults addressed by IEC TR 61641;
risks due to smoke emissions;
double faults, i.e. multiple phenomenon, potentially combined.
| Standards | Relationship |
| IEC TR 63054:2017 | Identical |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 60947-7-2:2009 | Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors |
| NFPA 921 : 2017 | GUIDE FOR FIRE AND EXPLOSION INVESTIGATIONS |
| IEC 60947-4-1:2009+AMD1:2012 CSV | Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters |
| IEC 60695-2-3:1984 | Fire hazard testing. Part 2: Test methods. Bad-connection test with heaters |
| IEC 60999-2:2003 | Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included) |
| IEC 60050-212:2010 | International Electrotechnical Vocabulary (IEV) - Part 212: Electrical insulating solids, liquids and gases |
| IEC 60695-2-11:2014 | Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) |
| IEC 60947-7-1:2009 | Low-voltage switchgear and controlgear - Part 7-1: Ancillary equipment - Terminal blocks for copper conductors |
| IEC 60999-1:1999 | Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included) |
| ISO/IEC Guide 51:2014 | Safety aspects — Guidelines for their inclusion in standards |
| IEC 60695-2-12:2010+AMD1:2014 CSV | Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods- Glow-wire flammability index (GWFI) test method for materials |
| IEC TR 61641:2014 | Enclosed low-voltage switchgear and controlgear assemblies - Guide for testing under conditions of arcing due to internal fault |
| IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV | Low-voltage switchgear and controlgear - Part 1: General rules |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| IEC 60695-1-21:2016 | Fire hazard testing - Part 1-21: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - Summary and relevance of test methods |
| IEC 60050-121:1998 | International Electrotechnical Vocabulary (IEV) - Part 121: Electromagnetism |
| IEC 60947-3:2008+AMD1:2012+AMD2:2015 CSV | Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units |
| IEC 62477-1:2012+AMD1:2016 CSV | Safety requirements for power electronic converter systems and equipment - Part 1: General |
| IEC 60947-2:2016 | Low-voltage switchgear and controlgear - Part 2: Circuit-breakers |
| IEC 60695-11-5:2016 | Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance |
| IEC 60947-6-1:2005+AMD1:2013 CSV | Low-voltage switchgear and controlgear - Part 6-1: Multiple functionequipment - Transfer switching equipment |
| IEC 60695-1-10:2016 | Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines |
| IEC GUIDE 116:2010 | Guidelines for safety related risk assessment and risk reduction for low voltage equipment |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.