PREN 1287 : DRAFT 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SANITARY TAPWARE - LOW PRESSURE THERMOSTATIC MIXING VALVES - GENERAL TECHNICAL SPECIFICATION
01-08-2017
19-06-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and units
5 Classification, designation
6 Designation
7 Marking/Identification
8 Materials
9 Dimensional characteristics
10 Backflow protection
11 Test sequence
12 Leaktightness
13 Performance
14 Pressure Resistance
15 Torsional resistance of the operating controls
16 Mechanical endurance characteristics
Annex A (normative) - Test Set-up Descriptions
Annex B (normative) - Measurements
Annex C (informative) - Temperature transit
Annex D (normative)
Bibliography
Defines general construction, performance and material requirements for PN 10 thermostatic mixing valves (TMV) and includes test methods for the verification of mixed water temperature performance at the point of use below 45 degrees C.
| Committee |
TC 164
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| 15/30321799 DC : 0 | Identical |
| 13/30280715 DC : 0 | Identical |
| PD 6504:1983 | Medical information on human reaction to skin contact with hot surfaces |
| EN 13202 : 2000 | ERGONOMICS OF THE THERMAL ENVIRONMENT - TEMPERATURES OF TOUCHABLE HOT SURFACES - GUIDANCE FOR ESTABLISHING SURFACE TEMPERATURE LIMIT VALUES IN PRODUCT STANDARDS WITH THE AID OF EN 563 |
| EN 246:2003 | Sanitary tapware - General specifications for flow rate regulators |
| EN 1112:2008 | Sanitary tapware - Shower outlets for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| EN 13618:2016 | Flexible hose assemblies in drinking water installations - Functional requirements and test methods |
| EN 1113:2015 | Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification |
| EN 1717:2000 | Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow |
| EN 563:1994/A1:1999/AC:2000 | SAFETY OF MACHINERY - TEMPERATURES OF TOUCHABLE SURFACES - ERGONOMICS DATA TO ESTABLISH TEMPERATURE LIMIT VALUES FOR HOT SURFACES |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISA MC96.1 : 1982 | TEMPERATURE MEASUREMENT THERMOCOUPLES |
| EN ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
| EN 13959:2004 | Anti-pollution check valves - DN 6 to DN 250 inclusive family E, type A, B, C and D |
| EN 200:2008 | Sanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification |
| ISO 9886:2004 | Ergonomics Evaluation of thermal strain by physiological measurements |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| EN 248:2002 | Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.