PREN 16506 : DRAFT 2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
01-10-2014
12-01-2013
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Pipes at the 'M'-Stage
6 Marking
7 Fittings at the 'M' stage
8 Lining system at the 'I' stage
9 Installation
10 Documentation
Annex A (normative) - Anchoring strength of plastics
inner layer - Test method for bond strength by
pull-off
Annex B (normative) - I - Stage crushing strength test
Bibliography
Describes performance requirements and describes test methods for pipes and fittings for the renovation of underground drain and sewer systems by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer.
| Committee |
TC 165
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| 12/30275810 DC : 0 | Identical |
| NF EN 16506 : 2014 | Identical |
| NEN EN 16506 : 2014 | Identical |
| EN 728:1997 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| EN 1107-2:2001 | Flexible sheets for waterproofing - Determination of dimensional stability - Part 2: Plastic and rubber sheets for roof waterproofing |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| EN 1542:1999 | Products and systems for the protection and repair of concrete structures - Test methods - Measurement of bond strength by pull-off |
| ISO 2039-1:2001 | Plastics — Determination of hardness — Part 1: Ball indentation method |
| EN ISO 6259-1:2015 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015) |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| EN 13380:2001 | General requirements for components used for renovation and repair of drain and sewer systems outside buildings |
| CEN/TR 14920:2005 | Jetting resistance of drain and sewer pipes - Moving jet test method |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 11296-1:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General |
| ISO 6259-1:2015 | Thermoplastics pipes Determination of tensile properties Part 1: General test method |
| EN 445:2007 | Grout for prestressing tendons - Test methods |
| EN 196-1:2016 | Methods of testing cement - Part 1: Determination of strength |
| EN ISO 75-2:2013 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
| ISO 4624:2016 | Paints and varnishes — Pull-off test for adhesion |
| ISO 11296-7:2011 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 7: Lining with spirally-wound pipes |
| EN 1979:1999 | Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam |
| EN ISO 2039-1:2003 | Plastics - Determination of hardness - Part 1: Ball indentation method (ISO 2039-1:2001) |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| EN ISO 4624:2016 | Paints and varnishes - Pull-off test for adhesion (ISO 4624:2016) |
| ISO 10544:1992 | Cold-reduced steel wire for the reinforcement of concrete and the manufacture of welded fabric |
| EN 1610:2015 | Construction and testing of drains and sewers |
| EN 13067:2012 | Plastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies |
| PREN ISO 11296-7 : DRAFT 2012 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NONPRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES (ISO 11296-7:2011) |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| EN 14117:2004 | Products systems for the protection and repair of concrete structures - Test methods - Determination of time of efflux of cementitious injection products |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.