Skip to content
Please enter a keyword to search

  • PREN ISO 15874-3 : DRAFT 2010

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 3: FITTINGS

    Available format(s): 

    Superseded date:  01-02-2013

    Language(s): 

    Published date:  12-01-2013

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions, symbols and
       abbreviated terms
    4 Material characteristics
    5 General characteristics
    6 Geometrical characteristics
    7 Mechanical characteristics of plastics fittings
    8 Physical and chemical characteristics of plastics
       components
    9 Sealing elements
    10 Performance requirements
    11 Marking
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines the characteristics of fittings for polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application.

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee TC 155
    Document Type Draft
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    National Adoptions - (Show below) - (Hide below)

    Equivalent Standard(s) Relationship
    10/30228356 DC : 0 Identical

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 1254-3:1998 Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes
    EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
    ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
    ISO 15874-1:2013 Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 1: General
    ISO 9080:2012 Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
    EN 681-2:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
    ISO 15874-2:2013 Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 2: Pipes
    ISO 12092:2000 Fittings, valves and other piping system components made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) for pipes under pressure Resistance to internal pressure Test method
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ENV 12108:2001 Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption
    ISO 15874-5:2013 Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 5: Fitness for purpose of the system
    ISO/TS 15874-7:2003 Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 7: Guidance for the assessment of conformity
    EN 10226-1:2004 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
    EN 12107 : 1997 PLASTICS PIPING SYSTEM - INJECTION MOULDED THERMOPLASTICS FITTINGS, VALVES AND ANCILLARY EQUIPMENT - DETERMINATION OF THE LONG-TERM HYDROSTATIC STRENGTH OF THERMOPLASTICS MATERIALS FOR INJECTION MOULDING OF PIPING COMPONENTS
    ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    ISO 7686:2005 Plastics pipes and fittings — Determination of opacity
    EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective