SAE AMS4037Q
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (2024; -T3 Flat Sheet, -T351 Plate) Solution Heat Treated
Available format(s)
Hardcopy , PDF
Superseded date
24-08-2020
Superseded by
Language(s)
English
Published date
29-12-2014
Publisher
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1 SCOPE
2 APPLICABLE DOCUMENTS
3 TECHNICAL REQUIREMENTS
4 QUALITY ASSURANCE PROVISIONS
5 PREPARATION FOR DELIVERY
6 ACKNOWLEDGEMENT
7 REJECTIONS
8 NOTES
This specification covers an aluminum alloy in the form of sheet and plate from 0.008 to 4.000 inches (0.20 to 101.60 mm) in thickness, inclusive (See 8.4).
| DevelopmentNote |
Supersedes SAE AMS 4033 (07/1999)
|
| DocumentType |
Standard
|
| Pages |
5
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This specification covers an aluminum alloy in the form of sheet and plate from 0.008 to 4.000 inches (0.20 to 101.60 mm) in thickness, inclusive (See 8.4).
| SAE AMS2482E | Hard Anodic Coating on Aluminum Alloys Polytetrafluoroethylene (PTFE)-Impregnated or Codeposited |
| SAE AMS 3116 A : 2005 | PRIMER COATING; EPOXY, CHEMICAL AND SOLVENT RESISTANT NON-CHROMATED, CORROSION PREVENTIVE |
| SAE AMS1630C | Cleaner, Carpet Shampoo Type |
| SAE ARP5485B | Endurance Time Test Procedures for SAE Type II/III/IV Aircraft Deicing/Anti-Icing Fluids |
| SAE AS5127B | Aerospace Standard Test Methods for Aerospace Sealants Methods for Preparing Aerospace Sealant Test Specimens |
| SAE AMS 3695 : 2014 | ADHESIVE FILM, EPOXY-BASE, FOR HIGH DURABILITY STRUCTURAL ADHESIVE BONDING |
| SAE AMS1428J | Fluid, Aircraft Deicing/Anti-Icing, Non-Newtonian (Pseudoplastic), SAE Types II, III, and IV |
| SAE AMS1435C | Fluid, Generic, Deicing/Anti-Icing Runways and Taxiways |
| SAE AMS2514A | Anodic Coating on Aluminum Alloys Sulfuric Acid Process, Resin-Sealed |
| SAE AMS1536B | Cleaner for Aircraft Components Cold Tank Type, Solvent-Base |
| SAE AMS3255B | Sealing Tape, Sheet, or Gasket, Polytetrafluoroethylene, Expanded (EPTFE) Oil and Water Resistant |
| SAE AMS3117 | Primer Zinc Molybdate |
| SAE AMS 3107 : 1983(R2014) | PRIMER, ADHESIVE, CORROSION-INHIBITING, FOR HIGH DURABILITY STRUCTURAL ADHESIVE BONDING |
| MIL-HDBK-510 Revision A:2014 | AEROSPACE FUELS CERTIFICATION |
| SAE AMS3263A | Sealing Compound, Polythioether, Ambient Cure or Immediate Heat Cure For Aircraft Structures, Fuel Resistant with Intermittent Use to 400°CF (204°CC) |
| SAE AMS1374A | Remover, Polyurethane/Epoxy Paint Alkaline, Hot-Tank Type |
| SAE ARP1675 | Structural Weldbonding of Aluminum Structures |
| SAE AMS3259B | Sealing Compound, Polythioether Nonchromated, Corrosion Inhibiting for Intermittent Use to 360°F (182°C) |
| SAE AMS 3688 : 2014 | ADHESIVE, FOAMING, HONEYCOMB CORE SPLICE, STRUCTURAL, -55 DEGREES C TO +82 DEGREES C (-65 DEGREES F TO +180 DEGREES F) |
| SAE AMS 3689 : 2014 | ADHESIVE, FOAMING, HONEYCOMB, CORE SPLICE, STRUCTURAL, -54 TO +177 DEGREES C (-65 TO +350 DEGREES F) |
| SAE AMS 3075 : 2016 | COMPOUND, CORROSION-PREVENTIVE HARD FILM, HOT APPLICATION |
| SAE AMS2472G | Anodic Treatment of Aluminum Alloys Sulfuric Acid Process, Dyed Coatings |
| SAE AMS 1453 : 2015 | DISINFECTANT CLEANER FOR AIRCRAFT INTERIOR GENERAL PURPOSE LIQUID |
| MIL-HDBK-510-1 Revision A:2010 | AEROSPACE FUELS CERTIFICATION |
| SAE AMS 2483 : 2015 | BLACKENING SOLUTION FOR ALUMINUM, TOUCH-UP SOLUTION |
| MIL-DTL-7034 Revision F:2005 | PULLEYS, GROOVE, ANTIFRICTION BEARING, GREASE LUBRICATED, AIRCRAFT, GENERAL SPECIFICATION FOR |
| BS M 75:1994 | Aircraft de-icing/anti-icing Newtonian fluids, ISO type I |
| MIL P 7034 : D | PULLEY, GROOVE, ANTIFRICTION BEARING, GREASE LUBRICATED, AIRCRAFT |
| SAE AMS4254C | Aluminum Alloy, Aramid Fiber Reinforced, Laminated Sheet 4.4Cu - 1.5Mg - 0.6Mn (2024-T3) 3, 5, 7, or 9 Ply |
| SAE AMS3077 | COMPOUND, CORROSION PREVENTIVE Soft Film, Thixotropic, Cold Application- |
| SAE AMS1424N | Fluid, Aircraft Deicing/Anti-Icing, SAE Type 1 |
| SAE ARP5945A | Endurance Time Test Procedures for SAE Type I Aircraft Deicing/Anti-Icing Fluids |
| SAE AMS1548B | Cleaner, Turbine Engine Gas Path Solvent Emulsion Type |
| SAE AMS3054C | Oil, Lubricating, Low Temperature For -55 °C (-67 °F) Service |
| SAE AMS 1377 : 2012 | REMOVER, PAINT, EPOXY AND POLYURETHANE PAINT SYSTEM, NON-CHLORINATED SOLVENT |
| SAE AMSP5315B | Acrylonitrile-butadiene (NBR) Rubber For Fuel-Resistant Seals 60 to 70 |
| SAE ARP1862A | CLEANING EFFICIENCY OF TURBINE ENGINE GAS PATH CLEANERS Laboratory Test Method |
| SAE AS5901C | Water Spray and High Humidity Endurance Test Methods for SAE AMS1424 and SAE AMS1428 Aircraft Deicing/Anti-icing Fluids |
| BS M 78:1995 | Aircraft de-icing/anti-icing non-Newtonian fluids, ISO type II |
| SAE AMS1426D | Fluid, Deicing/Anti-Icing, Runways and Taxiways Glycol Base |
| MIL-DTL-5541 Revision F:2006 | Chemical Conversion Coatings on Aluminum and Aluminum Alloys |
| SAE AMS 1375 : 2012 | REMOVER, PAINT, EPOXY AND POLYURETHANE PAINT SYSTEMS |
| SAE AMS1376B | Remover, Epoxy Paint Acid-Type, Thickened |
| SAE AMS2469J | Hard Anodic Coating on Aluminum and Aluminum Alloys |
| SAE AMS 1388 : 2008 | REMOVER, TEMPORARY COATING, ALKALINE TYPE, WATER BASE |
| SAE AMS1540C | Cleaner, Thrust Reverser Water-Base |
| SAE ARP 1755 : 2000 | EFFECT OF CLEANING AGENTS ON AIRCRAFT ENGINE MATERIALS, STOCK LOSS TEST METHOD |
| SAE AMS 7258 : 2001 | RINGS, SEALING, BUTADIENE-ACRYLONITRILE (NBR) RUBBER FUEL RESISTANT, LOW SHRINKAGE 65-75 |
| SAE AMS 1432 : 1995 | FLUID, DEICING/ANTI-ICING, RUNWAYS AND TAXIWAYS, POTASSIUM ACETATE BASE |
| SAE AMS1431D | Compound, Solid Runway and Taxiway Deicing/Anti-Icing |
| SAE AMS2471H | Anodic Treatment of Aluminum Alloys Sulfuric Acid Process, Undyed Coating |
| SAE AMS 3686 : 2014 | ADHESIVE, POLYIMIDE RESIN, FILM AND PASTE HIGH TEMPERATURE RESISTANT, 315 DEGREES C (599 DEGREES F) |
| SAE AMS1659 | COATING, SOIL BARRIER Semi-Permanent |
| MIL-DTL-81706 Revision B:2004 | Chemical Conversion Materials for Coating Aluminum and Aluminum Alloys |
| SAE AMS3095A | Paint: High Gloss For Airline Exterior System |
| SAE AMS2473H | Chemical Film Treatment for Aluminum Alloys General Purpose Coating |
| SAE AMS 1527 : 2014 | CLEANER FOR AIRCRAFT EXTERIOR SURFACES, WATER-MISCIBLE, FOAM-ON, PRESSURE-SPRAYING |
| SAE AMS2470N | Anodic Treatment of Aluminum Alloys Chromic Acid Process |
| SAE AS269J | Identification of Material for AN, MS, and AS Engine and Propeller Standard Utility Parts and Also for Company Parts |
| SAE AMS3159G | Leak Test Solution Liquid Oxygen Compatible |
| SAE AMS3529B | Plastic Sheet and Film, Vinyl Copolymers Unplasticized |
| SAE AMS3377A | Sealing Compound, Electrically Conductive Corrosion Inhibiting |
| SAE AMS3167B | Solvents, Wipe for Cleaning Prior to Application of Primer and Top Coat Materials, or Sealing Compounds |
| SAE AMS1631C | Cleaner, Carpet Water Extraction Type |
| ANSI H35.2 : 2017 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS |
| ASTM B 666/B666M : 2015 : REDLINE | Standard Practice for Identification Marking of Aluminum and Magnesium Products |
| SAE AMS2772G | Heat Treatment of Aluminum Alloy Raw Materials |
| SAE AS1990D | Aluminum Alloy Tempers |
| SAE AMS2355L | Quality Assurance, Sampling and Testing Aluminum Alloys and Magnesium Alloy Wrought Products (Except Forging Stock), and Rolled, Forged, or Flash Welded Rings |
| ASTM B 660 : 2015 : REDLINE | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ANSI H35.2M : 2013 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS (METRIC) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.