SAE AMS 4150 : 2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ALUMINUM ALLOY, EXTRUSIONS AND RINGS 1.0MG - 0.60SI - 0.28CU - 0.20CR - (6061-T6) SOLUTION AND PRECIPITATION HEAT TREATED
17-05-2019
01-01-2013
1 SCOPE
2 APPLICABLE DOCUMENTS
3 TECHNICAL REQUIREMENTS
4 QUALITY ASSURANCE PROVISIONS
5 PREPARATION FOR DELIVERY
6 ACKNOWLEDGEMENT
7 REJECTIONS
8 NOTES
Specifies an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing, flash welded rings fabricated from extruded stock, and stock for flash welded rings.
| Committee |
AMS-D
|
| DevelopmentNote |
Supersedes SAE AMS 4155 (07/1999)
|
| DocumentType |
Standard
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| QQ-A-200-8 Revision F:1983 | Similar to |
| MIL-DTL-28754-62 Revision A:2016 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER, CROSSOVER, CONTACT TAILS ON .050 CENTERS |
| MIL DTL 28754/60 : A | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER CONTACT TAILS ON .100 CENTERS |
| MIL-DTL-28754-59 Revision A:2016 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER CONTACT TAILS ON .100 CENTERS (CERAMIC COMPATIBLE) |
| MIL-DTL-83798 Revision D:2008 | FITTING, RUBBER HOSE, LIGHTWEIGHT, MEDIUM PRESSURE, GENERAL SPECIFICATION FOR |
| MIL-DTL-28754-101 Revision A:2015 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 0.6 PITCH, 250 CONTACT, CENTER |
| SAE AS 269J:2012:(S2018) | IDENTIFICATION OF MATERIAL FOR AN, MS AND AS ENGINE AND PROPELLER STANDARD UTILITY PARTS AND ALSO FOR COMPANY PARTS |
| MIL-DTL-28754-100 Revision A:2015 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 200 CONTACT, CENTER |
| MIL-DTL-28754-61 Revision A:2016 | Connectors, Electrical, Modular, Type IV, Connector, 100 Pin, Center, Crossover, Contact Tails on .100 Centers (Ceramic Compatible) |
| MIL-DTL-55302-78 Revision D:2004 | Connectors, Printed Circuit Subassembly and Accessories: Key, Polarizing, Connectors, Electrical Printed Wiring Boards |
| ANSI H35.2 : 2017 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS |
| ASTM B 807/B807M : 2013 : REDLINE | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys |
| ASTM B 666/B666M : 2015 : REDLINE | Standard Practice for Identification Marking of Aluminum and Magnesium Products |
| SAE AMS 7488F : 2013(R2018) | RINGS, FLASH WELDED, ALUMINUM AND ALUMINUM ALLOYS |
| SAE AMS 2772 : 2016 | HEAT TREATMENT OF ALUMINUM ALLOY RAW MATERIALS |
| SAE AS1990D:2003(S2016) | ALUMINUM ALLOY TEMPERS |
| SAE AMS 2355 : 2016 | QUALITY ASSURANCE, SAMPLING AND TESTING, ALUMINUM ALLOYS AND MAGNESIUM ALLOY, WROUGHT PRODUCTS (EXCEPT FORGING STOCK), AND ROLLED, FORGED, OR FLASH WELDED RINGS |
| ASTM B 660 : 2015 : REDLINE | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ANSI H35.2M : 2013 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS (METRIC) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.