Skip to content
Please enter a keyword to search

  • SAE AMS 5630 : 2013

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    STEEL, CORROSION-RESISTANT, BARS, WIRE, AND FORGINGS, 17CR - 0.52MO (0.95 - 1.20C) (440C)

    Available format(s): 

    Superseded date:  02-09-2022

    Language(s): 

    Published date:  09-04-2013

    Publisher:  SAE International

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. APPLICABLE DOCUMENTS
    3. TECHNICAL REQUIREMENTS
    4. QUALITY ASSURANCE PROVISIONS
    5. PREPARATION FOR DELIVERY
    6. ACKNOWLEDGMENT
    7. REJECTIONS
    8. NOTES

    Abstract - (Show below) - (Hide below)

    Specifies a corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.

    General Product Information - (Show below) - (Hide below)

    Committee AMS-F
    Document Type Revision
    Publisher SAE International
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    16/30354034 DC : 0 BS EN 4854-1 - AEROSPACE SERIES - BEARINGS, SPHERICAL PLAIN, IN CORROSION RESISTING STEEL WITH SELF-LUBRICATING LINER, LOW STARTING TORQUE AND LOW FRICTION COEFFICIENT, ELEVATED DUTY CYCLES UNDER LOW OSCILLATIONS AT DIFFERENT OPERATING CONDITIONS, NARROW SERIES - DIMENSIONS AND LOADS
    MIL-B-81819-1 Base Document:1983 BEARING, PLAIN, SLIDING SPHERICAL, SELF LUBRICATING, SELF ALIGNING HIGH SPEED OSCILLATION
    MIL-P-23460 Revision E:1991 PIN, QUICK-RELEASE, SELF-RETAINING POSITIVE-LOCKING
    MS17988 Revision E:1994 PIN QUICK RELEASE POSITIVE LOCKING DOUBLE ACTING T HANDLE
    MS17987 Revision G:1994 PIN, QUICK RELEASE, SELF-RETAINING, POSITIVE LOCKING, SINGLE ACTING, RING HANDLE
    MS17984 Revision F:1994 PIN QUICK RELEASE, SELF RETAINING POSITIVE LOCKING SINGLE ACTING BUTTON HANDLE
    MS17986 Revision G:1994 PIN, QUICK RELEASE, SELF-RETAINING, POSITIVE LOCKING, SINGLE ACTING, "L" HANDLE
    SAE AMS P 25732 : 1998 PACKAGING, PREFORMED, PETROLEUM HYDRAULIC FLUID RESISTANT, LIMITED SERVICE AT 275 DEGREES F (135 DEGREES C)
    ABMA B3.2 : 1992 AMERICAN NATIONAL STANDARD FOR ROLLING ELEMENT BEARINGS - AIRCRAFT ENGINE, ENGINE GEARBOX, AND ACCESSORY APPLICATIONS - SURFACE VISUAL INSPECTION
    NASM 23460 : 2004 PIN, QUICK-RELEASE, SELF-RETAINING, POSITIVE-LOCKING
    SAE AMS 3242 : 2011 CHLOROPRENE (CR) RUBBER, WEATHER RESISTANT, 75-85
    SAE AMS 3241 : 2011 CHLOROPRENE (CR) RUBBER, WEATHER RESISTANT, 55-65
    SAE ARP 5796 : 2013 FLIGHT CRITICAL CONTROL VALVES, MILITARY AIRCRAFT
    SAE AMS 3240 : 2011 CHLOROPRENE (CR) RUBBER, WEATHER RESISTANT, 35-45
    MIL-PRF-32287 Revision A:2011 PACKING, PREFORMED, PETROLEUM HYDRAULIC FLUID RESISTANT
    16/30354035 DC : 0 BS EN 4854-2 - AEROSPACE SERIES - BEARINGS, SPHERICAL PLAIN, IN CORROSION RESISTING STEEL WITH SELF-LUBRICATING LINER, LOW STARTING TORQUE AND LOW FRICTION COEFFICIENT, ELEVATED DUTY CYCLES UNDER LOW OSCILLATIONS AT DIFFERENT OPERATING CONDITIONS, WIDE SERIES - DIMENSIONS AND LOADS
    MIL PRF 0032287 : 0 PACKING, PREFORMED, PETROLEUM HYDRAULIC FLUID RESISTANT
    SAE AS 22227 : 2014(S2018) BEARING, BALL, ANNULAR, GENERATOR AND MOTOR GENERATOR
    TR 4661 : 2009 AEROSPACE SERIES - HINGES, FLIGHT CONTROLS MATERIALS AND SURFACE TREATMENTS
    MIL-STD-1647 Revision E:2003 IDENTIFICATION MARKINGS FOR DOMESTICALLY MANUFACTURED BEARINGS, BALL, ANNULAR FOR INSTRUMENTS AND PRECISION COMPONENTS
    SAE AS 269J:2012:(S2018) IDENTIFICATION OF MATERIAL FOR AN, MS AND AS ENGINE AND PROPELLER STANDARD UTILITY PARTS AND ALSO FOR COMPANY PARTS
    SAE AMS 7258 : 2001 RINGS, SEALING, BUTADIENE-ACRYLONITRILE (NBR) RUBBER FUEL RESISTANT, LOW SHRINKAGE 65-75
    SAE AMS P 5315 : 2013 ACRYLONITRILE-BUTADIENE (NBR) RUBBER FOR FUEL-RESISTANT SEALS 60 TO 70

    Standards Referencing This Book - (Show below) - (Hide below)

    SAE AMS 2241 : 2016 TOLERANCES, CORROSION AND HEAT-RESISTANT STEEL, IRON ALLOY, TITANIUM, AND TITANIUM ALLOY BARS AND WIRE
    SAE AMS 2248 : 2016 CHEMICAL CHECK ANALYSIS LIMITS, CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS, MARAGING AND OTHER HIGHLY-ALLOYED STEELS, AND IRON ALLOYS
    ASTM E 384 : 2017 : REDLINE Standard Test Method for Microindentation Hardness of Materials
    SAE AMS 2806D : 2013 IDENTIFICATION BARS, WIRE, MECHANICAL TUBING, AND EXTRUSIONS, CARBON AND ALLOY STEELS AND CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS
    SAE AS 1182 : 2012 STANDARD STOCK REMOVAL ALLOWANCE AIRCRAFT-QUALITY AND PREMIUM AIRCRAFT-QUALITY STEEL BARS AND MECHANICAL TUBING
    SAE AMS 2371 : 2016 QUALITY ASSURANCE SAMPLING AND TESTING, CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS, WROUGHT PRODUCTS AND FORGING STOCK
    ASTM E 353 : 2014 : REDLINE Standard Test Methods for Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys
    SAE AMS 2374 : 2016 QUALITY ASSURANCE SAMPLING AND TESTING CORROSION AND HEAT-RESISTANT STEEL AND ALLOY FORGINGS
    ASTM E 381 : 2017 : REDLINE Standard Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings
    SAE AMS 2808 : 2017 IDENTIFICATION FORGINGS
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective