SAE AMS1424N
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Fluid, Aircraft Deicing/Anti-Icing, SAE Type 1
Hardcopy , PDF
English
09-06-2017
06-10-2018
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. ACKNOWLEDGMENT
7. REJECTIONS
8. NOTES
APPENDIX A - ENVIRONMENTAL REQUIREMENTS AND TEST METHODS
Describes a deicing/anti-icing material in the form of a fluid.
| DevelopmentNote |
Supersedes MIL A 8243. (06/2004) Supersedes SAE AS 8243. (04/2010) Supersedes SAE AMS 1425. (06/2010) Supersedes SAE AMS 1427. (07/2010)
|
| DocumentType |
Standard
|
| Pages |
17
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This foundation specification (AMS1424N) and its associated category specifications (AMS1424/1 and AMS1424/2) cover a deicing/anti-icing material in the form of a fluid.
| SAE AMS4049M | Aluminum Alloy, Sheet and Plate, Alclad 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075; -T6 Sheet - T651 Plate) Solution and Precipitation Heat Treated |
| SAE AMS2475G | Protective Treatments Magnesium Alloys |
| ASTM D 1177 : 2017 : REDLINE | Standard Test Method for Freezing Point of Aqueous Engine Coolants |
| SAE AMS5886C | Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 50Ni - 20Cr - 20Co - 5.8Mo - 2.2Ti - 0.45Al Consumable Electrode or Vacuum Induction Melted 2100 °F (1149 °C) Solution Heat Treated |
| SAE AMS4911N | Titanium Alloy, Sheet, Strip, and Plate 6Al - 4V Annealed |
| SAE AMS4376H | Plate, Magnesium Alloy 3.0Al - 1.0Zn - 0.20Mn (AZ31B-H26) Cold Rolled and Partially Annealed |
| SAE AMS4037Q | Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (2024; -T3 Flat Sheet, -T351 Plate) Solution Heat Treated |
| CFR 40(PTS790-999) : JUL 2017 | PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY |
| MIL-STD-870 Revision C:2007 | Cadmium Plating, Low Embrittlement, Electrodepositon |
| ASTM E 70 | TEST METHOD FOR PH OF AQUEOUS SOLUTIONS WITH THE GLASS ELECTRODE |
| ASTM D 1331 : 2014 : REDLINE | Standard Test Methods for Surface and Interfacial Tension of Solutions of Paints, Solvents, Solutions of Surface-Active Agents, and Related Materials |
| SAE AMSP83310A | Plastic Sheet, Polycarbonate, Transparent |
| SAE AS5900C | Standard Test Method for Aerodynamic Acceptance of AMS1424 and AMS1428 Aircraft Deicing/Anti-Icing Fluids |
| SAE ARP 1917 : 2002 | CLARIFICATION OF TERMS USED IN AEROSPACE METALS SPECIFICATIONS |
| SAE AS6285 | Aircraft Ground Deicing/Anti-Icing Processes |
| SAE AMS1424/1 | Deicing/Anti-Icing Fluid, Aircraft SAE Type I Glycol (Conventional and Non-Conventional) Based |
| ASTM D 93 : 2016-07 | TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER |
| MIL-PRF-25690 Revision B:1993 | Plastic, Sheet and Formed Parts, Modified Acrylic Base, Monolithic, Crack Propagation Resistant |
| SAE AMS4916K | Titanium Alloy Sheet, Strip, and Plate 8Al - 1Mo - 1V Duplex Annealed |
| CFR 40(PTS136-149) : JUL 2017 | PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY |
| ASTM D 891 : 2009-04 | TEST METHODS FOR SPECIFIC GRAVITY, APPARENT, OF LIQUID INDUSTRIAL CHEMICALS |
| SAE AS5901C | Water Spray and High Humidity Endurance Test Methods for SAE AMS1424 and SAE AMS1428 Aircraft Deicing/Anti-icing Fluids |
| SAE AMS2470N | Anodic Treatment of Aluminum Alloys Chromic Acid Process |
| SAE AMS1424/2 | Deicing/Anti-Icing Fluid, Aircraft SAE Type I Non-Glycol Based |
| SAE AMS5045J | Steel, Sheet and Strip 0.25 Carbon, Maximum Hard Temper |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.