SAE AMS6325K
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Steel, Bars, and Forgings 0.50Cr - 0.55Ni - 0.25Mo (0.38 - 0.43C) (SAE 8740) Heat Treated, 105 ksi (724 MPa) Tensile Strength
Hardcopy , PDF
13-04-2020
English
20-12-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. ACKNOWLEDGMENT
7. REJECTIONS
8. NOTES
Specifies an aircraft-quality, low-alloy steel in the form of heat treated bars and forgings.
| DevelopmentNote |
Supersedes MIL S 6049 (09/2002) Supersedes SAE AMS S 6049. (07/2006)
|
| DocumentType |
Standard
|
| Pages |
7
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This specification covers an aircraft-quality, low-alloy steel in the form of heat treated bars and forgings.
| Standards | Relationship |
| MIL-S-6049 Revision A:1967 | Similar to |
| 17/30369678 DC : 0 | PREN 7010 - AEROSPACE SERIES - USER GUIDE FOR CREATION AND DESIGNATION OF BOLTS |
| MS21025 Revision F:1996 | NUT, CASTELLATED, HEXAGON |
| 10/30227763 DC : 0 | BS EN 6114 - AEROSPACE SERIES - BOLT, COUNTERSUNK HEAD, SHORT THREAD - INCH SERIES |
| SAE AS269J | Identification of Material for AN, MS, and AS Engine and Propeller Standard Utility Parts and Also for Company Parts |
| 10/30227764 DC : 0 | BS EN 6115 - AEROSPACE SERIES - BOLT - PROTRUDING HEAD, SHORT THREAD - INCH SERIES |
| MIL-DTL-8789 Revision G:2015 | FITTING END, ATTACHABLE, HYDRAULIC, HIGH PRESSURE (3,000 PSI), GENERAL SPECIFICATION FOR |
| SAE AMS2372G | Quality Assurance Sampling and Testing Carbon and Low-Alloy Steel Forgings |
| SAE AMS2370L | Quality Assurance Sampling and Testing Carbon and Low-Alloy Steel Wrought Products and Forging Stock |
| ASTM E 384 : 2017 : REDLINE | Standard Test Method for Microindentation Hardness of Materials |
| SAE AMS2251H | Tolerances Low-Alloy Steel Bars |
| SAE AMS 2806D : 2013 | IDENTIFICATION BARS, WIRE, MECHANICAL TUBING, AND EXTRUSIONS, CARBON AND ALLOY STEELS AND CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS |
| SAE AMS2301K | Steel Cleanliness, Aircraft Quality Magnetic Particle Inspection Procedure |
| SAE AS1182C | Standard Stock Removal Allowance Aircraft-Quality and Premium Aircraft-Quality Steel Bars and Mechanical Tubing |
| SAE AMS2750E | Pyrometry |
| ASTM E 350 : 2012-09 | TEST METHODS FOR CHEMICAL ANALYSIS OF CARBON STEEL, LOW-ALLOY STEEL, SILICON ELECTRICAL STEEL, INGOT IRON, AND WROUGHT IRON |
| SAE AMS2759/1E | Heat Treatement of Carbon and Low-Alloy Steel Parts Minimum Tensile Strength Below 220 ksi (1517 MPa) |
| ASTM E 381 : 2017 : REDLINE | Standard Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings |
| SAE AMS2808E | Identification Forgings |
| SAE AMS2259E | Chemical Check Analysis Limits Wrought Low-Alloy and Carbon Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.