SAE ARP1110C
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Minimizing Stress Corrosion Cracking in Wrought Forms of Steels and Corrosion Resistant Steels and Alloys
Hardcopy , PDF
25-01-2021
English
10-08-2015
1. SCOPE
2. REFERENCES
3. GENERAL
4. PREVENTION
5. NOTES
Gives the aerospace industry with recommendations concerning the minimization of stress corrosion cracking in wrought heat-treatable carbon and low alloy steels and in austenitic, precipitation hardenable, and martensitic corrosion-resistant steels and alloys.
DocumentType |
Standard
|
Pages |
5
|
PublisherName |
SAE International
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide the aerospace industry with recommendations concerning the minimization of stress corrosion cracking in wrought heat-treatable carbon and low alloy steels and in austenitic, precipitation hardenable, and martensitic corrosion-resistant steels and alloys.The detailed recommendations are based on laboratory and field experience and reflect those design practices and fabrication procedures which should avoid in-service stress corrosion cracking.
SAE AMS5524L | Steel, Corrosion and Heat-Resistant, Sheet, Strip and Plate 18Cr - 13Ni - 2.5Mo (SAE 30316) Solution Heat Treated |
SAE AMS 5864 : 2013 | STEEL, CORROSION-RESISTANT, PLATE 13CR - 8.0NI - 2.2MO - 1.1AL VACUUM INDUCTION PLUS CONSUMABLE ELECTRODE MELTED SOLUTION HEAT TREATED, PRECIPITATION HARDENABLE |
SAE AMS6425D | Steel, Bars, Forgings, and Tubing 1.4Mn - 1.5Si - 0.30Cr - 1.8Ni - 0.40Mo (0.23 - 0.28C) Consumable Electrode Vacuum Melted |
SAE AMS5629H | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 13Cr - 8.0Ni - 2.2Mo - 1.1Al Vacuum Induction Plus Consumable Electrode Melted Solution Heat Treated, Precipitation Hardenable |
SAE AMS5622F | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb - 4.0Cu Solution Heat Treated, Precipitation Hardenable Consumable Electrode Remelted |
SAE AMS6411J | Steel Bars, Forgings, and Tubing 0.88Cr - 1.8Ni - 0.42Mo - 0.08V (0.28 - 0.33C) (4330 Mod) Consumable Electrode Remelted |
SAE AMS5643V | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb (Nb) - 4.0Cu Solution Heat Treated, Precipitation Hardenable |
SAE AMS5344F | Steel, Corrosion-Resistant, Investment Castings 16Cr - 4.1Ni - 0.28Cb - 3.2Cu Homogenization, Solution, and Precipitation Heat Treated (H900) 180 ksi (1241 MPa) Tensile Strength (17-4) |
SAE AMS6526H | Steel, Bars, Forgings, Tubing, and Rings 1.0Cr - 7.5Ni - 4.5Co - 1.0Mo - 0.09V (0.29 - 0.34C) Consumable Electrode Vacuum Remelted, Annealed |
SAE AMS5621G | Steel, Corrosion Resistant, Bars, Wire, and Forgings 13Cr (0.30–0.40C) (51420) Annealed |
SAE MAM6415C | Steel, Bars, Forgings, and Tubing, 0.80cr 1.8ni 0.25mo (0.38 0.43) |
SAE AMS6499A | Steel, Bars, Forgings, and Tubing 2.7Si - 0.85Cr - 1.8Ni - 0.4Mo - 0.2V - (0.37 - 0.44C) Double Vacuum Melted |
SAE AMS6427M | Steel Bars, Forgings, and Tubing 0.88Cr - 1.8Ni - 0.42Mo - 0.08V (0.28 - 0.33C) (4330 Mod) |
SAE AMS5611F | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 12Cr Ferrite Controlled, Consumable Electrode Melted |
SAE AMS5604J | Steel, Corrosion Resistant, Sheet, Strip, and Plate 16.5Cr - 4.0Ni - 4.0Cu - 0.30Cb Solution Heat Treated, Precipitation Hardenable |
SAE AMS6382P | Steel, Bars, Forgings, and Rings 0.95Cr - 0.20Mo (0.38 - 0.43C) (SAE 4140) Annealed |
SAE AMS6419H | Steel, Bars, Forgings, and Tubing 1.6Si - 0.82Cr - 1.8Ni - 0.40Mo - 0.08V (0.40 - 0.45C) Consumable Electrode Vacuum Remelted |
SAE AMS6359K | Steel, Sheet, Strip, and Plate 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340) |
SAE AMS6417H | Steel, Bars, Forgings, and Tubing 1.6Si - 0.82Cr - 1.8Ni - 0.40Mo - 0.08V (0.38 - 0.43C) Consumable Electrode Vacuum Remelted |
SAE AMS5342E | Steel, Corrosion-Resistant, Investment Castings 16Cr - 4.1Ni - 0.28Cb (Nb) - 3.2Cu Homogenization, Solution, and Precipitation Heat Treated (H1100) 130 ksi (896 MPa) Tensile Strength (17-4) |
SAE AMS5620G | Steel, Corrosion and Heat-Resistant, Bars, Wire, and Forgings 13Cr (0.30 - 0.40C) (SAE 51420F, 51420FSe) Free-Machining Grade |
SAE AMS6409E | Steel, Bars, Forgings, and Tubing 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340) Special Aircraft Quality Cleanliness Normalized and Tempered |
SAE AMS6482A | Steel Bars, Forgings, and Tubing 1.5Si - 1.25Cr - 3.8Ni - 0.50Mo - 0.30V (0.40C) Vacuum Remelted Annealed |
SAE AMS5578G | Steel, Corrosion and Heat-Resistant, Welded Tubing 12Cr - 8.5Ni - 0.30Cb - 1.1Ti - 2.0Cu Vacuum Induction Plus Consumable Electrode Vacuum Melted Solution Heat Treated, Precipitation Hardenable |
SAE AMS5568H | Steel, Corrosion and Heat Resistant, Welded Tubing 17Cr - 7.1Ni - 1.1Al Solution Heat Treated, Precipitation-Hardenable |
SAE AMS6484E | Steel, Bars, Forgings, and Tubing 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340) Normalized and Tempered |
SAE AMS5343E | Steel, Corrosion-Resistant, Investment Castings 16Cr - 4.1Ni - 0.28Cb (Nb) - 3.2Cu Homogenization, Solution, and Precipitation Heat Treated (H1000) 150 ksi (1034 MPa) Tensile Strength (17-4) |
SAE AMS5934B | Steel, Extra High Toughness, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 13Cr - 8.0Ni - 2.2Mo - 1.1Al Vacuum Induction Plus Consumable Electrode Melted Solution Heat Treated, Precipitation-Hardenable |
SAE AMS6415U | Steel, Bars, Forgings, and Tubing 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340) |
SAE AMS6414M | Steel, Bars, Forgings, and Tubing 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340) Vacuum Consumable Electrode Remelted |
SAE AMS5529J | Steel, Corrosion Resistant, Sheet and Strip 17Cr - 7.1Ni - 1.1Al Solution Heat Treated and Cold Rolled, Precipitation Hardenable 0.0015 to 0.100 inch (0.038 to 2.54 mm) Nominal Thickness |
SAE AMS6428K | Steel, Bars, Forgings, and Tubing 0.78Cr - 1.8Ni - 0.35Mo - 0.20V (0.32 - 0.38C) (4335 Mod) |
SAE AMS5955B | Steel, Corrosion-Resistant, Bars, Wire, and Forgings 10Cr - 12Ni - 2Mo - 1.45Al - 1.15Ti Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated, Precipitation Hardenable |
SAE AMS6340B | Steel Bars, Forgings, and Tubing 0.88Cr - 1.8Ni - 0.42Mo - 0.08V (0.28 – 0.33C) (4330 Mod) Consumable Electrode Vacuum Remelted |
SAE AMS6429H | Steel Bars, Forgings, Tubing, and Rings 0.78Cr - 1.8Ni - 0.35Mo - 0.20V (0.33 - 0.38C) (4335 Mod) Consumable Electrode Vacuum Melted |
SAE AMS5612J | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 12Cr Ferrite Controlled, Annealed |
SAE AMS6408E | Steel, Hotwork Tool, Bars and Forgings 5.25Cr - 1.5Mo - 1.0V (0.35-0.45C) (H-13) Electroslag Remelted (ESR) or Consumable Electrode Vacuum Arc Remelted (VAR) Annealed |
SAE AMS5659S | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu |
SAE AMS6474B | Forgings, Hardenable Steels and Corrosion-Resistant Steels Heat-Treated, Finished-Part Properties Short-Transverse Tensile Strength and Fracture Toughness |
SAE AMS5591K | Steel, Corrosion and Heat-Resistant, Tubing, Seamless 12.5Cr (SAE 51410) Annealed |
SAE AMS5357D | Steel, Corrosion-Resistant, Investment Castings 15Cr - 4.6Ni - 0.22Cb - 2.8Cu Solution Heat Treated, Precipitation Hardenable |
SAE AMS5763E | Steel, Corrosion Resistant Bars, Forgings, Tubing, and Rings 15Cr - 6.5Ni - 0.75Mo - 0.50Cb (Nb) - 1.5Cu Solution Heat Treated |
SAE AMS5773E | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Tubing, and Rings 15Cr - 6.5Ni - 0.75Mo - 0.30 Cb (Nb) - 1.5Cu Consumable Electrode Remelted, Solution Heat Treated Precipitation Hardenable |
SAE AMS5862M | Steel, Corrosion-Resistant, Sheet, Strip, and Plate 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu Consumable Electrode Remelted, Solution Heat Treated Precipitation-Hardenable |
SAE AMS5863E | Steel, Corrosion Resistant, Sheet, Strip, and Plate 15Cr - 6.5Ni - 0.75Mo - 0.60Cb - 1.5Cu Solution Heat Treated, Precipitation Hardenable |
SAE AMS5860F | Steel, Corrosion-Resistant, Sheet, Strip, and Plate 12Cr - 8.5Ni - 0.30Cb - 1.1Ti - 2.0Cu Multiple Melted, Solution Heat Treated, Precipitation Hardenable |
SAE AMS6487L | Steel, Bars, and Forgings 5.0Cr - 1.3Mo - 0.50V (0.38 - 0.43C) (H-11) Consumable Electrode Vacuum Melted |
SAE AMS5859D | Steel, Corrosion Resistant, Sheet, Strip, and Plate 15Cr - 6.5Ni - 0.75Mo - 0.30Cb - 1.5Cu Consumable Electrode Melted, Solution Heat Treated Precipitation Hardenable |
SAE AMS6454E | Steel, Sheet, Strip, and Plate 1.8Ni - 0.80Cr - 0.25Mo (0.38 - 0.43C) (SAE 4340) Vacuum Consumable Electrode Remelted |
SAE AMS6257F | Steel Bars, Forgings, and Tubing 1.6Si - 0.82Cr - 1.8Ni - 0.40Mo - 0.08V (0.40 - 0.44C) Consumable Electrode Vacuum Remelted Normalized and Tempered |
SAE AMS5628F | Steel, Corrosion-Resistant, Bars, Wire, Forgings, and Tubing 16Cr - 2.5Ni (SAE 51431) |
SAE AMS5609E | Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 12Cr - 0.12Cb (Nb) (410 Modified) Ferrite Controlled, Annealed |
SAE AMS5612K | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings, 12Cr Ferrite Controlled, Annealed |
SAE AMS 2432 : 2013 | SHOT PEENING, COMPUTER MONITORED |
SAE AMS2430T | Shot Peening, Automatic |
SAE AMS2432D | Shot Peening, Computer Monitored |
SAE AMS2431C | Peening Media General Requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.