SAE AS4604B
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hose Assembly, 3000 psi, Polytetrafluoroethylene, Metallic Reinforced, 400 °F, Heavy Duty, Aircraft Hydraulic Systems
23-09-2020
07-01-2013
1 SCOPE
2 APPLICABLE DOCUMENTS
3 TECHNICAL REQUIREMENTS
4 QUALITY ASSURANCE PROVISIONS
5 PREPARATION FOR DELIVERY
6 NOTES
Specifies requirements for heavy-duty polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in 400 degree F, 3000 psi aircraft hydraulic systems.
| DocumentType |
Standard
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| Supersedes |
This SAE Aerospace Standard (AS) defines the requirements for heavy-duty polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in 400 °F, 3000 psi aircraft hydraulic systems. Assemblies are suitable where rapid rate pressure pulsing and torsional/ longitudinal flexing may occur, in addition to normal hydraulic system loads.
| SAE AS150F | Hose Assembly, Type Classifications of, Basic Performance and Fire Resistance |
| SAE AMS5689F | Steel, Corrosion and Heat Resistant, Wire 18Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated |
| SAE AIR4298 | Impulse Test Machine, Sine Wave, Equipment and Operation of |
| SAE AMS5659S | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu |
| SAE AMS5645S | Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 10Ni - 0.40Ti (321) Solution Heat Treated |
| SAE ARP1835 | Preparation for Delivery, General Requirements for Hose Assemblies |
| SAE ARP603G | Impulse Testing of Hydraulic Hose, Tubing, and Fittings Assemblies |
| SAE AS611E | Hose Assembly and Tubing, Polytetrafluoroethylene, Cleaning Methods for |
| ASTM A 262 : 2015 : REDLINE | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| SAE AS4703A | FITTING END, ACORN, SHORT FLARELESS, DESIGN STANDARD |
| MIL-STD-130 Revision N:2007 | IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY |
| ASTM B 348 : 2013 : REDLINE | Standard Specification for Titanium and Titanium Alloy Bars and Billets |
| SAE AMS 2488 : 2000 | ANODIC TREATMENT - TITANIUM AND TITANIUM ALLOYS SOLUTION PH 13 OR HIGHER |
| NAS1760:2015 | FITTING END, FLARELESS ACORN, STANDARD DIMENSIONS FOR |
| MIL-PRF-7808 Revision L:1997 | LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE |
| SAE AMS5571J | Steel, Corrosion and Heat-Resistant, Seamless Tubing 18Cr - 10.5Ni - 0.70Cb (Nb) (347) Solution Heat Treated |
| SAE AMS5643U | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb (Nb) - 4.0Cu Solution Heat Treated, Precipitation Hardenable |
| SAE AS4395B | FITTING END, FLARED, TUBE CONNECTION, DESIGN STANDARD |
| SAE AMS5743J | Steel, Corrosion and Heat-Resistant, Bars and Forgings 15.5Cr - 4.5Ni - 2.9Mo - 0.10N Solution Heat Treated, Sub-Zero Cooled, Equalized, and Over-Tempered |
| SAE AS1055D | Fire Testing of Flexible Hose, Tube Assemblies, Coils, Fittings, and Similar System Components |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AS4658 | FITTING END, EXTERNAL THREAD, SHORT FLARELESS, DESIGN STANDARD |
| SAE AMS5647K | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 9.5Ni Solution Heat Treated |
| SAE ARP908C | Torque Requirements, Installation and Qualification Test, Hose and Tube Fitting |
| SAE AMS4965L | Titanium Alloy, Bars, Wire, Forgings, and Rings 6.0Al 4.0V Solution Heat Treated and Aged |
| SAE AMSQQP35 | Passivation Treatments for Corrosion-Resistant Steel |
| MIL-STD-831 Base Document:1963 | TEST REPORTS, PREPARATION OF |
| SAE AMS5567F | Steel, Corrosion Resistant, Seamless or Welded Hydraulic Tubing 19Cr - 10Ni (304) Solution Heat Treated |
| SAE AIR 1228 : 2009 | STANDARD IMPULSE MACHINE EQUIPMENT AND OPERATION |
| SAE AS4265 | Impulse Testing of Hydraulic Tubing and Fittings, S-N Curve |
| SAE AMS5646P | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 11Ni - 0.60Cb(Nb) (347) Solution Heat Treated |
| SAE AMS5688L | Steel, Corrosion-Resistant, Wire 18Cr - 9.0Ni (SAE 30302) Spring Temper |
| SAE AMS4945F | Titanium Alloy Tubing, Seamless, Hydraulic 3Al - 2.5V, Controlled Contractile Strain Ratio Cold Worked, Stress Relieved |
| SAE AS 8879 : 2004 | SCREW THREADS - UNJ PROFILE, INCH CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER |
| SAE AS1072F | Sleeve, Hose Assembly, Fire Protection |
| SAE AMS5575P | Steel, Corrosion and Heat-Resistant, Welded Tubing 18Cr - 10.5Ni - 0.70Cb (Nb) (347) Solution Heat Treated |
| SAE AMS5570Q | Steel, Corrosion and Heat-Resistant, Seamless Tubing 18Cr - 11Ni - 0.40Ti (321) Solution Heat Treated |
| QQ-S-763 Revision F:1996 | STEEL BARS, WIRE, SHAPES AND FORGINGS; CORROSION RESISTANT |
| SAE AS2078A | Test Methods, Hose Assemblies, Polytetrafluoroethylene (PTFE) |
| MIL-STD-100 Revision G:1997 | ENGINEERING DRAWINGS |
| MIL-PRF-83282 Revision D:1997 | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, METRIC, NATO CODE NUMBER H-537 |
| SAE AMS5639J | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 10Ni Solution Heat Treated |
| MIL H 5606 : G | HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT; MISSILE AND ORDNANCE |
| SAE AS4375C | FITTING END, FLARELESS, DESIGN STANDARD |
| SAE AS150E | Hose Assembly, Type Classifications of, Basic Performance and Fire Resistance |
| SAE AS4488 | Tubular Assemblies, Fusion Welded, Inspection Processes and Acceptance Standards For |
| SAE AMS5644E | Steel, Bars and Forgings, Corrosion Resistant 17Cr - 7Ni - 1Al |
| SAE AMS5556J | Steel, Corrosion and Heat-Resistant, Seamless or Welded Hydraulic Tubing 18Cr - 11Ni - 0.70Cb (347) Solution Heat Treated |
| MIL-F-85421 Revision B:1986 | FITTINGS, TUBE, FLUID SYSTEMS, SEPARABLE, BEAM SEAM, 3000/4000 PSI - GENERAL SPECIFICATION FOR |
| SAE AMS4928V | Titanium Alloy Bars, Wire, Forgings, Rings, and Drawn Shapes 6Al - 4V Annealed |
| SAE AMS5557J | Steel, Corrosion and Heat-Resistant, Seamless or Welded Hydraulic Tubing 18.5Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.