SAE AS 5377 : 2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
NUT, SELF-LOCKING, 0.7500 THRU 1.5000 THREAD SIZES, UNS S66286, 160,000 PSI, 800 DEGREE F, UNJ THREAD - PROCUREMENT SPECIFICATION
24-09-2020
01-01-2000
1 SCOPE
2 REFERENCES
3 TECHNICAL REQUIREMENTS
4 QUALITY ASSURANCE PROVISIONS
5 PREPARATION FOR DELIVERY
6 ACKNOWLEDGEMENT
7 REJECTIONS
8 NOTES
APPENDIX A MEASUREMENT OF PERPENDICULARITY VARIATION OF
THE BEARING SURFACE
APPENDIX B WRENCH TORQUE TEST
APPENDIX C PERMANENT SET TEST
APPENDIX D REUSABILITY TEST AT ROOM TEMPERATURE, AFTER
BAKING
APPENDIX E REUSABILITY TEST AT ROOM TEMPERATURE AS
RECEIVED CONDITION
APPENDIX F 3-CYCLE TEST AT ROOM TEMPERATURE
Covers the requirements for self-locking wrenchable nuts with thread sizes 0.7500 thru 1.5000 inches.
| Committee |
E-25
|
| DocumentType |
Standard
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy |
| SAE AS 5447 : 2012 | ACCEPTANCE CRITERIA FOR NUTS - MAGNETIC, PARTICLE, FLUORESCENT PENETRANT, AND VISIBLE PENETRANT EXAMINATION |
| MS33787 Revision D:1984 | WRENCHING ELEMENT, EXTERNAL SPLINE, DIMENSIONS FOR |
| SAE AMS 5663 : 2016 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, BARS, FORGINGS, AND RINGS 52.5NI - 19CR - 3.0MO - 5.1CB (NB) - 0.90TI - 0.50AL - 18FE CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED 1775 DEGREES F (968 DEGREES C) SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 5737 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS AND TUBING, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1650 DEGREES F (899 DEGREES C), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AS 7467 : 2013 | BOLTS AND SCREWS, NICKEL ALLOY, UNS N07718, TENSILE STRENGTH 185 KSI, STRESS RUPTURE RATED, PROCUREMENT SPECIFICATION |
| MIL-PRF-7808 Revision L:1997 | LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE |
| MIL-W-8982 Revision D:1989 | WRENCHES, SPLINED, HIGH STRENGTH, THIN WALL, GENERAL SPECIFICATION FOR |
| SAE AMS 2759/3 : 2015 | HEAT TREATMENT PRECIPITATION-HARDENING CORROSION-RESISTANT, MARAGING, AND SECONDARY HARDENING STEEL PARTS |
| SAE AMS 5853 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS AND WIRE, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED 1800 DEGREES F (982 DEGREES C) SOLUTION TREATED AND WORK-STRENGTHENED, 160 KSI (1103 MPA) TENSILE STRENGTH |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AS 7466 : 2014 | BOLTS AND SCREWS, NICKEL ALLOY, UNS N07718, TENSILE STRENGTH 185 KSI, FATIGUE RATED, PROCUREMENT SPECIFICATION |
| GGG-W-636 Revision E:1975 | WRENCHES (BOX, OPEN END, AND COMBINATION) |
| SAE AMS 5734 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, AND TUBING, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1650 DEGREES F (899 DEGREES C) SOLUTION HEAT TREATED |
| SAE AS 870 : 2015 | WRENCHING CONFIGURATION, BI-HEXAGONAL (12 POINT) DRIVE, DESIGN STANDARD FOR |
| SAE AMS 5732 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING AND RINGS, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED 1800 DEGREES F (982 DEGREES C), SOLUTION AND PRECIPITATION HEAT TREATED |
| NASM1312-6:2013 | FASTENER TEST METHODS, METHOD 6, HARDNESS |
| SAE AS 8879 : 2004 | SCREW THREADS - UNJ PROFILE, INCH CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER |
| SAE AMS 5731 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1800 DEGREES F (982 DEGREES C) SOLUTION HEAT TREATED |
| SAE AMS 2411 : 2013 | PLATING, SILVER FOR HIGH TEMPERATURE APPLICATIONS |
| SAE AS 5054 : 2012 | AREAS FOR CALCULATING STRESS OF LOAD VALUES FOR EXTERNALLY AND INTERNALLY THREADED FASTENERS |
| SAE AS 5443 : 2012 | WRENCHING ELEMENT, SPLINE DRIVE - DIMENSIONS FOR |
| SAE AIR 1471 : 2000 | TORQUE TIGHTENING THREADED FASTENERS |
| NASM 1312-8 : 2001 | FASTENER TEST METHODS, METHOD 8, TENSILE STRENGTH |
| SAE AS 1310 : 2012 | FASTENER TORQUE FOR THREADED APPLICATIONS, DEFINITIONS OF |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.