SAE AS4897
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Hose Assembly, Polytetrafluoroethylene (PTFE), Low Pressure, 450 °F and Fireproof, Procurement Specification for
Hardcopy , PDF
03-09-2019
English
27-07-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1 SCOPE
2 APPLICABLE DOCUMENTS
3 REQUIREMENTS
4 QUALITY ASSURANCE PROVISIONS
5 PREPARATION FOR DELIVERY
6 NOTES
Specifies the requirements for polytetrafluoroethylene (PTFE) hose assemblies for use in aerospace fuel and lubricating oil systems at temperatures between -67 and 450 degrees F and at operating pressures.
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy |
This SAE Aerospace Standard (AS) covers the requirements for polytetrafluoroethylene (PTFE) hose assemblies for use in aerospace fuel and lubricating oil systems at temperatures between -67 and 450 °F and at operating pressures per Table 1. The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems where some gaseous diffusion through the wall of the PTFE liner can be tolerated.The use of these hose assemblies in pneumatic storage systems is not recommended. In addition, installations in which the limits specified herein are exceeded, or in which the application is not covered specifically by this document, for example oxygen, shall be subject to the approval of the purchaser.
| SAE AS150F | Hose Assembly, Type Classifications of, Basic Performance and Fire Resistance |
| SAE AIR 5693 : 2014 | COMPATIBILITY OF PTFE HOSE ASSEMBLIES WITH TYPICAL FLUIDS FOUND IN AEROSPACE APPLICATIONS |
| SAE AMS5689F | Steel, Corrosion and Heat Resistant, Wire 18Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated |
| SAE AMS5659S | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu |
| SAE AMS5645S | Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 10Ni - 0.40Ti (321) Solution Heat Treated |
| SAE ARP1835 | Preparation for Delivery, General Requirements for Hose Assemblies |
| SAE ARP603G | Impulse Testing of Hydraulic Hose, Tubing, and Fittings Assemblies |
| SAE AS611E | Hose Assembly and Tubing, Polytetrafluoroethylene, Cleaning Methods for |
| ASTM A 262 : 2015 : REDLINE | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| MIL-STD-130 Revision N:2007 | IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY |
| QQ-P-35 Revision C:1988 | PASSIVATION TREATMENTS FOR CORROSION-RESISTANT STEEL |
| NAS1760:2015 | FITTING END, FLARELESS ACORN, STANDARD DIMENSIONS FOR |
| MIL-T-8808 Revision B:1981 | TUBING, STEEL, CORROSION RESISTANT (18.8 STABILIZED) AIRCRAFT HYDRAULIC QUALITY |
| MIL H 25579 : E | HOSE ASSEMBLY, TETRAFLUOROETHYLENE, HIGH TEMPERATURE MEDIUM PRESSURE, GENERAL REQUIREMENTS FOR |
| SAE AS1708F | FITTING END, INTERNAL FLARE, DESIGN STANDARD |
| SAE AMS5643U | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb (Nb) - 4.0Cu Solution Heat Treated, Precipitation Hardenable |
| SAE AS4395B | FITTING END, FLARED, TUBE CONNECTION, DESIGN STANDARD |
| SAE AMS5743J | Steel, Corrosion and Heat-Resistant, Bars and Forgings 15.5Cr - 4.5Ni - 2.9Mo - 0.10N Solution Heat Treated, Sub-Zero Cooled, Equalized, and Over-Tempered |
| SAE AMS5697F | Steel, Corrosion-Resistant, Wire 19Cr - 9.5Ni (SAE 30304) Solution Heat Treated |
| SAE AMS5690M | Steel, Corrosion and Heat Resistant, Wire 17Cr - 12Ni - 2.5Mo (316) Solution Heat Treated |
| SAE AS1055D | Fire Testing of Flexible Hose, Tube Assemblies, Coils, Fittings, and Similar System Components |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| SAE ARP1153A | Method for Determining Relative Specific Gravity Polytetrafluoroethylene Tubing |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AMS5647K | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 9.5Ni Solution Heat Treated |
| SAE ARP908C | Torque Requirements, Installation and Qualification Test, Hose and Tube Fitting |
| SAE AMS4965L | Titanium Alloy, Bars, Wire, Forgings, and Rings 6.0Al 4.0V Solution Heat Treated and Aged |
| MS33656 Revision J:1987 | FITTING END, STANDARD DIMENSIONS FOR FLARED TUBE CONNECTION AND GASKET SEAL |
| MIL-STD-831 Base Document:1963 | TEST REPORTS, PREPARATION OF |
| SAE AMS5637H | Steel, Corrosion Resistant, Bars and Wire 18Cr - 9.0Ni (SAE 30302) Solution Heat Treated, Cold Drawn and Stress Relieved 125 ksi (862 MPa) Tensile Strength |
| SAE AMS5646P | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 11Ni - 0.60Cb(Nb) (347) Solution Heat Treated |
| SAE AMS4945F | Titanium Alloy Tubing, Seamless, Hydraulic 3Al - 2.5V, Controlled Contractile Strain Ratio Cold Worked, Stress Relieved |
| MIL-S-8879 Revision C:1991 | SCREW THREADS, CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER, GENERAL SPECIFICATION FOR |
| SAE AMS5685L | Steel, Corrosion Resistant, Safety Wire, 18Cr - 11.5Ni (SAE 30305), Solution Heat Treated, Cold Finished |
| QQ-S-763 Revision F:1996 | STEEL BARS, WIRE, SHAPES AND FORGINGS; CORROSION RESISTANT |
| SAE AS2078A | Test Methods, Hose Assemblies, Polytetrafluoroethylene (PTFE) |
| SAE AMS5639J | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 10Ni Solution Heat Treated |
| SAE AS1946E | Hose Assembly, Polytetrafluoroethylene, Metallic Reinforced, Up to 1500 psi and 450 °F, Hydraulic and Pneumatic |
| SAE AS4375C | FITTING END, FLARELESS, DESIGN STANDARD |
| MIL-C-5501 Revision G:1989 | CAP AND PLUG, PROTECTIVE, DUST AND MOISTURE SEAL |
| SAE AS150E | Hose Assembly, Type Classifications of, Basic Performance and Fire Resistance |
| SAE AMS5644E | Steel, Bars and Forgings, Corrosion Resistant 17Cr - 7Ni - 1Al |
| MS33514 Revision G:1990 | FITTING END, STANDARD DIMENSIONS FOR FLARELESS TUBE CONNECTION AND GASKET SEAL (ASG) |
| SAE AMS4928V | Titanium Alloy Bars, Wire, Forgings, Rings, and Drawn Shapes 6Al - 4V Annealed |
| MIL T 31000 : 0 | TECHNICAL DATA PACKAGES - GENERAL SPECIFICATION FOR |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.