SAE AS5377
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Nut, Self-Locking, 0.7500 thru 1.5000 Thread Sizes, UNS S66286, 160,000 psi, 800 °F, UNJ Thread - Procurement Specification
23-08-2018
24-09-2020
1 SCOPE
2 REFERENCES
3 TECHNICAL REQUIREMENTS
4 QUALITY ASSURANCE PROVISIONS
5 PREPARATION FOR DELIVERY
6 ACKNOWLEDGEMENT
7 REJECTIONS
8 NOTES
APPENDIX A MEASUREMENT OF PERPENDICULARITY VARIATION OF
THE BEARING SURFACE
APPENDIX B WRENCH TORQUE TEST
APPENDIX C PERMANENT SET TEST
APPENDIX D REUSABILITY TEST AT ROOM TEMPERATURE, AFTER
BAKING
APPENDIX E REUSABILITY TEST AT ROOM TEMPERATURE AS
RECEIVED CONDITION
APPENDIX F 3-CYCLE TEST AT ROOM TEMPERATURE
Covers the requirements for self-locking wrenchable nuts with thread sizes 0.7500 thru 1.5000 inches.
| DocumentType |
Standard
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy |
This specification establishes the requirements for self-locking wrenchable nuts with thread sizes 0.7500 thru 1.5000 inches.The nuts are made of corrosion and heat resistant precipitation hardenable iron base alloy of the type identified under the Unified Numbering System as UNS S66286 and of 160,000 psi axial tensile strength at room temperature, with maximum conditioning temperature of parts at 800 °F.
| SAE AS5447 | Acceptance Criteria for Nuts - Magnetic Particle, Fluorescent Penetrant, and Visible Penetrant Examination |
| MS33787 Revision D:1984 | Wrenching Element, External Spline, Dimensions for |
| SAE AMS5663N | Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 52.5Ni - 19Cr - 3.0Mo - 5.1Cb (Nb) - 0.90Ti - 0.50Al - 18Fe Consumable Electrode or Vacuum Induction Melted 1775 °F (968 °C) Solution and Precipitation Heat Treated |
| SAE AS7467B | Bolts and Screws, Nickel Alloy, UNS N07718 Tensile Strength 185 ksi Stress Rupture Rated Procurement Specification |
| MIL-PRF-7808 Revision L:1997 | Lubricating Oil, Aircraft Turbine Engine, Synthetic Base |
| MIL-W-8982 Revision D:1989 | Wrenches, Splined, High Strength, Thin Wall, General Specification For |
| SAE AMS2759/3F | Heat Treatment Precipitation-Hardening Corrosion-Resistant and Maraging Steel Parts |
| SAE AMS5853C | Steel, Corrosion and Heat-Resistant, Bars and Wire 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Melted 1800 °F (982 °C) Solution Treated and Work-Strengthened 160 ksi (1103 MPa) Tensile Strength |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AS7466E | Bolts and Screws, Nickel Alloy, UNS N07718 Tensile Strength 185 ksi, Fatigue Rated, Procurement Specification |
| GGG-W-636 Revision E:1975 | WRENCH, (BOX, OPEN END, AND COMBINATION) (NO S/S DOCUMENT) |
| SAE AS870E | WRENCHING CONFIGURATION, BI-HEXAGONAL (12 POINT) DRIVE, DESIGN STANDARD FOR |
| SAE AS 8879 : 2004 | SCREW THREADS - UNJ PROFILE, INCH CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER |
| SAE AMS2411H | Plating, Silver for High Temperature Applications |
| SAE AS5054A | Areas for Calculating Stress or Load Values for Externally and Internally Threaded Fasteners |
| SAE AS5443A | WRENCHING ELEMENT, SPLINE DRIVE - DIMENSIONS FOR |
| SAE AIR1471A | Torque Tightening Threaded Fasteners |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.