SAE AS9006A

Introduction
1 Scope
  1.1 General
  1.2 Application
2 Normative references
3 Terms and definitions
4 Quality management system
  4.1 General requirements
  4.2 Documentation requirements
      4.2.1 General
      4.2.2 Quality manual
      4.2.3 Control of documents
      4.2.4 Control of records
  4.3 Configuration management
5 Management responsibility
  5.1 Management commitment
  5.2 Customer focus
  5.3 Quality policy
  5.4 Planning
      5.4.1 Quality objectives
      5.4.2 Quality management system planning
  5.5 Responsibility, authority and communication
      5.5.1 Responsibility and authority
      5.5.2 Management representative
      5.5.3 Internal communication
  5.6 Management review
      5.6.1 General
      5.6.2 Review input
      5.6.3 Review output
6 Resource Management
  6.1 Provision of resources
  6.2 Human resources
      6.2.1 General
      6.2.2 Competence, awareness and training
  6.3 Infrastructure
  6.4 Work environment
7 Product realization
  7.1 Planning of product realization
  7.2 Customer-related processes
      7.2.1 Determination of requirements related to the product
      7.2.2 Review of requirements to the product
      7.2.3 Customer communication
  7.3 Design and development
      7.3.1 Design and development planning
      7.3.2 Design and development inputs
      7.3.3 Design and development outputs
      7.3.4 Design and development review
      7.3.5 Design and development verification
      7.3.6 Design and development validation
      7.3.7 Control of design and development changes
  7.4 Purchasing
      7.4.1 Purchasing process
      7.4.2 Purchasing information
      7.4.3 Verification of purchased product
  7.5 Production and service provision
      7.5.1 Control of production and service provision
      7.5.2 Validation of processes for production and service provision
      7.5.3 Identification and traceability
      7.5.4 Customer property
      7.5.5 Preservation of product
  7.6 Control of monitoring and measuring devices
8 Measurement, analysis and improvement
  8.1 General
  8.2 Monitoring and measurement
      8.2.1 Customer satisfaction
      8.2.2 Internal audit
      8.2.3 Monitoring and measurement of processes
      8.2.4 Monitoring and measurement of product
  8.3 Control of nonconforming product
  8.4 Analysis of data
  8.5 Improvement
      8.5.1 Continual improvement
      8.5.2 Corrective action
      8.5.3 Preventive action
Annex A Bibliography

Includes quality system requirements for suppliers of products that contain deliverable embedded or loadable airborne, spaceborne or ground support software components that are part of an aircraft Type Design, weapon system, missile or spacecraft operational software and/or support software that is used in the development and maintenance of deliverable software.

The basic requirements of AS9100A apply with the following clarifications.This document supplements the requirements of AS9100A for deliverable software.This supplement contains Quality System requirements for suppliers of products that contain deliverable embedded or loadable airborne, spaceborne or ground support software components that are part of an aircraft Type Design, weapon system, missile or spacecraft operational software and/or support software that is used in the development and maintenance of deliverable software. This includes the host operating system software including assemblers, compilers, linkers, loaders, editors, code generators, analyzers, ground simulators and trainers, flight test data reduction, etc., that directly support creation, test and maintenance of the deliverable software. Where Commercial-Off-The-Shelf (COTS) or non-developmental components are integrated into a deliverable product, the organization and the customer shall agree on the extent of applicability of this supplement. The organization shall demonstrate that the software development infrastructure is in compliance with AS9100.This document also applies to firmware as defined herein. It does not apply to programmable logic devices, including fuse-link or reconfigurable parts such as Application Specific Integrated Circuits, (ASIC) or Field Programmable Gate Arrays (FPGA). ASICS AND FPGA’S are addressed by RTCA/DO-254.