SAE J 617 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ENGINE FLYWHEEL HOUSING AND MATING TRANSMISSION HOUSING FLANGES
Hardcopy , PDF
06-10-2020
English
01-01-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. REFERENCES
3. DIMENSIONS AND TOLERANCES
4. ENGINE FLYWHEEL HOUSINGS
5. MATING TRANSMISSION HOUSING FLANGES
6. NOTES
This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges.
| DocumentType |
Revision
|
| Pages |
8
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| SAE J 1033 : 2012 | PROCEDURE FOR MEASURING BORE AND FACE RUNOUT OF FLYWHEELS, FLYWHEEL HOUSINGS, AND FLYWHEEL HOUSING ADAPTERS |
| SAE J 1806 : 2017 | CLUTCH DIMENSIONS FOR TRUCK AND BUS APPLICATIONS |
| SAE J 2407 : 2017 | CLUTCH INSTALLATION AND RELEASE LINKAGE REQUIREMENTS FOR TRUCK AND BUS APPLICATION |
| SAE J 2408 : 2018 | CLUTCH REQUIREMENTS FOR HIGH-TORQUE TRUCK AND BUS ENGINES |
| SAE J 620 : 2012 | FLYWHEELS FOR INDUSTRIAL ENGINES USED WITH INDUSTRIAL POWER TAKE-OFFS EQUIPPED WITH DRIVING-RING TYPE OVERCENTER CLUTCHES AND ENGINE-MOUNTED MARINE GEARS AND SINGLE BEARING ENGINE-MOUNTED POWER GENERATORS |
| HI 1.3 : 2013 | ROTODYNAMIC CENTRIFUGAL PUMPS FOR DESIGN AND APPLICATION |
| SAE J 2555 : 2017 | Vehicle Idle Gear Rattle Evaluation Procedure<br> |
| SAE J 1463 : 2012 | PULL-TYPE CLUTCH TRANSMISSION INSTALLATION DIMENSIONS |
| SAE J 2469 : 2017 | CLUTCH APPLICATION POWERTRAIN STARTABILITY RATING REQUIREMENTS FOR TRUCK AND BUS APPLICATIONS |
| ANSI Y14.5 : 1973 | DIMENSIONING AND TOLERANCING FOR ENGINEERING DRAWINGS |
| SAE J 621 : 2012 | INDUSTRIAL POWER TAKE-OFFS WITH DRIVING RING TYPE OVERCENTER CLUTCHES |
| SAE J 543 : 1995 | STARTING MOTOR PINIONS AND RING GEARS |
| ANSI B11 : 2008 | GENERAL SAFETY REQUIREMENTS COMMON TO ANSI B11 MACHINES |
| SAE J 927 : 1995 | FLYWHEELS FOR ENGINE MOUNTED TORQUE CONVERTERS |
| SAE J542:1991 | STARTING MOTOR MOUNTINGS |
| ISO 7649:1991 | Clutch housings for reciprocating internal combustion engines Nominal dimensions and tolerances |
| SAE J 616 : 1995 | ENGINE FOOT MOUNTING (FRONT AND REAR) |
| ISO 7648:1987 | Flywheel housings for reciprocating internal combustion engines Nominal dimensions and tolerances |
| SAE J 1033 : 2012 | PROCEDURE FOR MEASURING BORE AND FACE RUNOUT OF FLYWHEELS, FLYWHEEL HOUSINGS, AND FLYWHEEL HOUSING ADAPTERS |
| SAE J 1172 : 2012 | ENGINE FLYWHEEL HOUSINGS WITH SEALED FLANGES |
| SAE J 615 : 1995 | ENGINE MOUNTINGS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.