SAE J2202_201604
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Heavy-Duty Wiring Systems for On-Highway Trucks
Hardcopy , PDF
06-12-2019
English
06-04-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. REFERENCES
3. DEFINITIONS
4. TESTS
5. REQUIREMENTS
6. DESIGN REQUIREMENTS
7. HARNESS ASSEMBLY CONSTRUCTION
8. CIRCUIT IDENTIFICATION
9. HARNESS ROUTING AND PROTECTION
10. GUIDELINES
11. SERIAL COMMUNICATIONS
12. VEHICLE GROUNDING
13. TRUCK TRACTOR OUTPUT FOR TRAILER ABS
14. TRACTOR TO TRAILER CABLE
15. NOTES
Gives general guidelines on the material selection, construction and qualification of components and wiring systems used to construct wiring systems for Heavy Duty Vehicles.
| DocumentType |
Standard
|
| Pages |
19
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This SAE Recommended Practice provides general guidelines on the material selection, construction and qualification of components and wiring systems used to construct wiring systems for Heavy Duty Vehicles The guidelines are limited to primary wiring systems of less than 50 V and includes cable sizes American Wire Gage 20 to AWG 4 on heavy-duty on-highway trucks. The document identifies appropriate operating performances requirements. This document excludes the male to female connection of the SAE J560 connectors.
| SAE J2394_201712 | Seven Conductor Cable for ABS Power - Truck and Bus |
| SAE J3082_201511 | Auxiliary Two Conductor Electrical Power Connector for Truck-Trailer High Power Jumper Cable |
| NFPA 1906 : 2016 | WILDLAND FIRE APPARATUS |
| NFPA 1901:2016 | AUTOMOTIVE FIRE APPARATUS |
| SAE J2174_201510 | Heavy-Duty Wiring Systems for Trailers 2032 mm or More in Width |
| NFPA 414 : 2017 | AIRCRAFT RESCUE AND FIRE-FIGHTING VEHICLES |
| SAE J1939/13_201610 | Off-Board Diagnostic Connector |
| NFPA 1917 : 2016 | AUTOMOTIVE AMBULANCES |
| SAE J2577_201509 | Heavy Duty Lamp Electrical Connector Standard |
| SAE J2742_201304 | Combination 11 Conductors and 4 Pairs ECBS Cable |
| NFPA 414:2020 | Standard for Aircraft Rescue and Fire-Fighting Vehicles |
| SAE J 1614 : 2010 | WIRING DISTRIBUTION SYSTEMS FOR OFF-ROAD, SELF-PROPELLED WORK MACHINES |
| SAE J1678_201512 | Low Voltage Ultra Thin Wall Primary Cable |
| SAE J1888_199011 | HIGH CURRENT TIME LAG ELECTRIC FUSES |
| SAE J2030_201506 | Heavy-Duty Electrical Connector Performance Standard |
| SAE J156_201603 | Fusible Links |
| SAE J1939/15_201508 | Physical Layer, 250 Kbps, Un-Shielded Twisted Pair (UTP) |
| SAE J2223/3_201112 | Connections for On-Board Road Vehicle Electrical Wiring Harnesses - Part 3: Multipole Connectors - Flat Blade Terminals - Dimensional Characteristics and Specific Requirements |
| SAE J560_201604 | Primary and Auxiliary Seven Conductor Electrical Connector for Truck-Trailer Jumper Cable |
| SAE J1493_201309 | Guarding of Starter System Energization |
| SAE J1128_201512 | Low Voltage Primary Cable |
| SAE J1455_201703 | Recommended Environmental Practices for Electronic Equipment Design in Heavy-Duty Vehicle Applications |
| SAE J1908_201302 | Electrical Grounding Practice |
| SAE J2247_201309 | Truck Tractor Power Output for Trailer ABS |
| SAE J1284_198804 | BLADE TYPE ELECTRIC FUSES |
| SAE J2549_201603 | Single Conductor Cable for Heavy-Duty Applications - Truck and Bus |
| SAE J553_201607 | Circuit Breakers |
| SAE J2223/2_201102 | Connections for On-Board Road Vehicle Electrical Wiring Harnesses—Part 2: Tests and General Performance Requirements |
| SAE J1939_201308 | Serial Control and Communications Heavy Duty Vehicle Network - Top Level Document |
| SAE J1811_201301 | Power Cable Terminals |
| MIL-STD-1344 Revision A:1977 | TEST METHODS FOR ELECTRICAL CONNECTORS |
| SAE J2497_201207 | Power Line Carrier Communications for Commercial Vehicles |
| SAE J2222_201210 | Coiled Electrical Cable - Truck and Bus |
| SAE J2394_201302 | Seven Conductor Cable for ABS Power - Truck and Bus |
| ISO 22241-1:2006 | Diesel engines NOx reduction agent AUS 32 Part 1: Quality requirements |
| SAE J1127_201512 | Low Voltage Battery Cable |
| SAE J163_201102 | Low Tension Wiring and Cable Terminals and Splice Clips |
| SAE J1939/11_201612 | Physical Layer, 250 Kbps, Twisted Shielded Pair |
| SAE J2223/1_201112 | Connections for On-Board Road Vehicle Electrical Wiring Harnesses - Part 1: Single-Pole Connectors - Flat Blade Terminals - Dimensional Characteristics and Specific Requirements |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| SAE J1067_201610 | Seven Conductor Cable - Truck and Bus |
| SAE J1939/14_201612 | Physical Layer, 500 Kbps |
| SAE J2191_201402 | Recommended Practice for Identification of Standardized Truck and Tractor Electrical Circuits |
| SAE J1939/13_201610 | Off-Board Diagnostic Connector |
| SAE J561_201011 | Electrical Terminals—Eyelet and Spade Type |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.