SAE J617_201404
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Engine Flywheel Housing and Mating Transmission Housing Flanges
Hardcopy , PDF
06-10-2020
English
16-04-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. REFERENCES
3. DIMENSIONS AND TOLERANCES
4. ENGINE FLYWHEEL HOUSINGS
5. MATING TRANSMISSION HOUSING FLANGES
6. NOTES
This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges.
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face.This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded.This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.
| SAE J1033_201206 | Procedure for Measuring Bore and Face Runout of Flywheels, Flywheel Housings, and Flywheel Housing Adapters |
| SAE J1806_201708 | Clutch Dimensions for Truck and Bus Applications |
| SAE J2407_201711 | Clutch Installation and Release Linkage Requirements for Truck and Bus Application |
| SAE J2408_201801 | Clutch Requirements for High-Torque Truck and Bus Engines |
| SAE J620_201210 | Flywheels for Industrial Engines Used With Industrial Power Take-Offs Equipped With Driving-Ring Type Overcenter Clutches and Engine-Mounted Marine Gears and Single Bearing Engine-Mounted Power Generators |
| HI 1.3 : 2013 | ROTODYNAMIC CENTRIFUGAL PUMPS FOR DESIGN AND APPLICATION |
| SAE J2555_201709 | Vehicle Idle Gear Rattle Evaluation Procedure |
| SAE J1463_201211 | Pull-Type Clutch Transmission Installation Dimensions |
| SAE J2469_201709 | Clutch Application Powertrain Startability Rating Requirements for Truck and Bus Applications |
| ANSI Y14.5 : 1973 | DIMENSIONING AND TOLERANCING FOR ENGINEERING DRAWINGS |
| SAE J621_201210 | Industrial Power Take-Offs With Driving Ring-Type Overcenter Clutches |
| SAE J543_199511 | STARTING MOTOR PINIONS AND RING GEARS |
| ANSI B11 : 2008 | GENERAL SAFETY REQUIREMENTS COMMON TO ANSI B11 MACHINES |
| SAE J927_199503 | FLYWHEELS FOR ENGINE-MOUNTED TORQUE CONVERTERS |
| SAE J542_199106 | STARTING MOTOR MOUNTINGS |
| ISO 7649:1991 | Clutch housings for reciprocating internal combustion engines Nominal dimensions and tolerances |
| SAE J616_199507 | ENGINE FOOT MOUNTING (FRONT AND REAR) |
| ISO 7648:1987 | Flywheel housings for reciprocating internal combustion engines Nominal dimensions and tolerances |
| SAE J1033_201206 | Procedure for Measuring Bore and Face Runout of Flywheels, Flywheel Housings, and Flywheel Housing Adapters |
| SAE J1172_201210 | Engine Flywheel Housings with Sealed Flanges |
| SAE J615_199507 | ENGINE MOUNTINGS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.