SAE J826_201511
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Devices for Use in Defining and Measuring Vehicle Seating Accommodation
Hardcopy , PDF
07-07-2021
English
10-11-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. REFERENCES
3. DEFINITIONS
4. H-POINT TEMPLATE - DESCRIPTION, APPLICATION,
AND POSITIONING PROCEDURE
5. H-POINT MACHINE - DESCRIPTION, APPLICATION,
AND INSTALLATION PROCEDURE
6. SHORT-COUPLED SEATING CONDITION
7. LONG-COUPLED SEATING CONDITION
8. DETERMINATION OF CUSHION ANGLE
9. H-POINT MACHINE AND TEMPLATE FABRICATION
10. CALIBRATION OF THE H-POINT MACHINE
11. NOTES
APPENDIX A - INSTALLATION PROCEDURE FOR SHORT - AND
LONG-COUPLED SEATING
APPENDIX B - DETERMINATION OF CUSHION ANGLE
APPENDIX C - SAE J826 H-POINT MACHINE CALIBRATION
INSPECTION
APPENDIX D - HEAD RESTRAINT MEASURING DEVICE (HRMD)
Describes the means by which passenger compartment dimensions can be obtained using a deflected seat rather than a free seat contour as a reference for defining seating space.
| DocumentType |
Standard
|
| Pages |
31
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
The devices of this SAE Standard provide the means by which passenger compartment dimensions can be obtained using a deflected seat rather than a free seat contour as a reference for defining seating space. All definitions and dimensions used in conjunction with this document are described in SAE J1100. These devices are intended only to apply to the driver side or center occupant seating spaces and are not to be construed as instruments which measure or indicate occupant capabilities or comfort. This document covers only one H-point machine installed on a seat during each test. Certified H-point templates and machines can be purchased from:SAE International400 Commonwealth DriveWarrendale, PA 15096-0001Specific procedures are included in Appendix A for seat measurements in short- and long-coupled vehicles and in Appendix B for measurement of the driver seat cushion angle. Specifications and a calibration inspection procedure for the H-point machine are given in Appendix C. Additional considerations are necessary when a Head Restraint Measuring Device (HRMD) is mounted to an H-point machine (Appendix D).
| ISO/TR 17950:2016 | Impact test procedures for road vehicles Rear seat positioning procedures for Hybrid III 5th percentile female dummy |
| SAE J2292_201601 | Combination Pelvic and Upper Torso Operator and Occupant Restraint Systems for Off-Road Work Machines |
| SAE AS 6316 : 2017 | PERFORMANCE STANDARDS FOR OBLIQUE FACING PASSENGER SEATS IN TRANSPORT AIRCRAFT |
| 04/301211 DC : DRAFT JAN 2004 | ISO 17373 - ROAD VEHICLES - SLED TEST PROCEDURE FOR EVALUATION OF CERVICAL SPINE INJURY RISK IN LOW-SPEED, REAR-END IMPACT |
| PREN 4723 : DRAFT 2013 | AEROSPACE SERIES - STANDARDIZED MEASUREMENT METHODS FOR COMFORT AND LIVING SPACE CRITERIA FOR AIRCRAFT PASSENGER SEATS |
| NFPA 1906 : 2016 | WILDLAND FIRE APPARATUS |
| NFPA 1901:2016 | AUTOMOTIVE FIRE APPARATUS |
| SAE J899_201205 | Operator\'s Seat Dimensions for Off-Road Self-Propelled Work Machines |
| 09/30177728 DC : 0 | BS ISO 4513 - ROAD VEHICLES - VISIBILITY - METHOD OF ESTABLISHMENT OF EYELLIPSES FOR DRIVER'S EYE LOCATION |
| SAE J1241_199911 | Fuel and Lubricant Tanks for Motorcycles |
| SAE J826/1_201106 | CAD Model for SAE J826® 3-D H-Point Machine |
| SAE AS8049/1A | Performance Standards for Side-Facing Seats in Civil Rotorcraft, Transport Aircraft, and General Aviation Aircraft |
| SAE J782_201411 | Motor Vehicle Seating Manual |
| SAE J2896_201201 | Motor Vehicle Seat Comfort Performance Measures |
| SAE AS8049C | Performance Standard for Seats in Civil Rotorcraft, Transport Aircraft, and General Aviation Aircraft |
| ISO 4513:2010 | Road vehicles Visibility Method for establishment of eyellipses for driver's eye location |
| VDI 4499 Blatt 4:2015-03 | Digital factory - Ergonomic representation of humans in the digital factory |
| SAE J383_201410 | Motor Vehicle Seat Belt Anchorages - Design Recommendations |
| SAE J1834_201401 | Seat Belt Comfort, Fit, and Convenience - Truck and Bus |
| BS ISO 17949 : 2013 | IMPACT TEST PROCEDURES FOR ROAD VEHICLES - SEATING AND POSITIONING PROCEDURES FOR ANTHROPOMORPHIC TEST DEVICES - PROCEDURE FOR THE WORLDSID 5OTH PERCENTILE MALE SIDE-IMPACT DUMMY IN FRONT OUTBOARD SEATING POSITIONS |
| PD ISO/TR 17950:2016 | Impact test procedures for road vehicles. Rear seat positioning procedures for Hybrid III 5th percentile female dummy |
| SAE J2422_201002 | Cab Roof Strength Evaluation—Quasi-Static Loading Heavy Trucks |
| ISO 20176:2011 | Road vehicles H-point machine (HPM-II) Specifications and procedure for H-point determination |
| ISO 17949:2013 | Impact test procedures for road vehicles — Seating and positioning procedures for anthropomorphic test devices — Procedure for the WorldSID 5Oth percentile male side-impact dummy in front outboard seating positions |
| BS ISO 4513:2010 | Road vehicles. Visibility. Method for establishment of eyellipses for driver\'s eye location |
| BS ISO 17373:2005 | Road vehicles. Sled test procedure for evaluating occupant head and neck interactions with seat/head restraint designs in low-speed rear-end impact |
| NFPA 1917 : 2016 | AUTOMOTIVE AMBULANCES |
| ISO 17373:2005 | Road vehicles Sled test procedure for evaluating occupant head and neck interactions with seat/head restraint designs in low-speed rear-end impact |
| EN 4723:2015 | Aerospace series - Standardized measurement methods for comfort and living space criteria for aircraft passenger seats |
| SAE J2287_201209 | Recommended Design and Performance Standard for Seats with Integrated Lap and Shoulder Restraints |
| SAE J1369_201208 | Anchorage Provisions for Installation of Child Restraint Tether Straps in Rear Seating Positions |
| 12/30275037 DC : 0 | BS EN 4723 - AEROSPACE SERIES - STANDARDIZED MEASUREMENT METHODS FOR COMFORT AND LIVING SPACE CRITERIA FOR AIRCRAFT PASSENGER SEATS |
| BS EN 4723:2015 | Aerospace series. Standardized measurement methods for comfort and living space criteria for aircraft passenger seats |
| SAE J2421_199801 | COE Frontal Strength Evaluation—Quasi-Static |
| DIN 70020-1:1993-02 | ROAD VEHICLES - AUTOMOTIVE ENGINEERING - DIMENSIONAL TERMS |
| SAE J2423_199801 | Cab Roof Strength Evaluation—Dynamic Loading Heavy Trucks |
| BS ISO 20176:2011 | Road vehicles. H-point machine (HPM-II). Specifications and procedure for H-point determination |
| SAE J1163_201608 | Determining Seat Index Point |
| SAE J287_201603 | Driver Hand Control Reach |
| I.S. EN 4723:2015 | AEROSPACE SERIES - STANDARDIZED MEASUREMENT METHODS FOR COMFORT AND LIVING SPACE CRITERIA FOR AIRCRAFT PASSENGER SEATS |
| SAE ARP6316 | Performance Standards for Oblique Facing Passenger Seats in Transport Aircraft |
| SAE J4004_200808 | Positioning the H-Point Design Tool—Seating Reference Point and Seat Track Length |
| SAE J4002_201001 | H-Point Machine (HPM-II) Specifications and Procedure for H-Point Determination—Auditing Vehicle Seats |
| SAE J1517_201110 | Driver Selected Seat Position for Class B Vehicles - Seat Track Length and SgRP |
| SAE J1100_200911 | Motor Vehicle Dimensions |
| SAE J182_201507 | Motor Vehicle Fiducial Marks and Three-dimensional Reference System |
| SAE J4003_200810 | H-Point Machine (HPM-II)—Procedure for H-Point Determination—Benchmarking Vehicle Seats |
| SAE J2732_200806 | Motor Vehicle Seat Dimensions |
| SAE J1516_201110 | Accommodation Tool Reference Point for Class B Vehicles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.