SAE MA 1573 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
NUT, SELF-LOCKING, STEEL, CLASS 1100 MPA/235 DEGREES C, MJ THREAD PROCUREMENT SPECIFICATION FOR, METRIC
Hardcopy , PDF
31-12-2022
English
15-11-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. ACKNOWLEDGEMENT
7. REJECTIONS
8. NOTES
APPENDIX A - MEASUREMENT OF PERPENDICULARITY VARIATION OF THE
BEARING SURFACE
APPENDIX B - WRENCH TORQUE TEST
APPENDIX C - PUSH-OUT TEST
APPENDIX D - TORQUE-OUT TEST
APPENDIX E - PERMANENT SET TEST
APPENDIX F - REUSABILITY TEST AT ROOM TEMPERATURE, AFTER BAKING
APPENDIX G - REUSABILITY TEST AT ROOM TEMPERATURE, AT RECEIVED
CONDITION
APPENDIX H - THREE-CYCLE TEST AT ROOM TEMPERATURE
APPENDIX J - ACCEPTANCE CRITERIA OF SURFACE DISCONTINUITIES ON
SELF-LOCKING NUTS
Describes the requirements for the following types of self-locking nuts: a. Wrenching nuts: that is, hex, double hex, spline drive b. Anchor nuts: that is, plate nuts, gang channel nuts, shank nuts.
| Committee |
E-25
|
| DocumentType |
Standard
|
| Pages |
39
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ISO 5855-2:1999 | Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts |
| SAE MA 1586 : 2013 | WRENCH CONFIGURATION, 12 SPLINE DRIVE, METRIC |
| SAE AMS 6322 : 2014 | STEEL BARS, FORGINGS, AND RINGS, 0.50CR - 0.55NI - 0.25MO (0.38 - 0.43C) (SAE 8740) |
| MIL-PRF-7808 Revision L:1997 | LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE |
| MIL-STD-2073-1 Revision E:2008 | STANDARD PRACTICE FOR MILITARY PACKAGING |
| ISO 965-2:1998 | ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality |
| SAE AMS 2759 : 2014 | HEAT TREATMENT OF STEEL PARTS, GENERAL REQUIREMENTS |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AMS 5085 : 2017 | STEEL SHEET, STRIP, AND PLATE, 0.48 - 0.55C (SAE 1050) |
| NASM1312:2012 | FASTENER TEST METHODS METHOD 11 TENSION FATIGUE |
| NA 0012 : REV 2 | FIXTURE, BEARING SURFACE SQUARENESS TEST, SELF-LOCKING NUTS, METRIC |
| SAE AMS 6304 : 2016 | LOW-ALLOY STEEL, HEAT-RESISTANT, BARS, FORGINGS, AND TUBING, 0.95CR - 0.55MO - 0.30V (0.40 - 0.50C) |
| SAE AMS 6300 : 2015 | STEEL BARS AND FORGINGS, 0.25MO (0.35 - 0.40C) (SAE 4037) |
| SAE AMS 2350 : 1989 | STANDARDS AND TEST METHODS |
| NAM 1312/113 : REV 1 | FASTENER TEST METHODS, METRIC METHOD 113 DOUBLE SHEAR TEST |
| SAE AMS 6351 : 2015 | STEEL, SHEET, STRIP, AND PLATE, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130), SPHEROIDIZED |
| ASTM E 1444 : 2005 | Standard Practice for Magnetic Particle Testing |
| MA1520A : 2012(R2018) | AREAS FOR CALCULATING STRESS OR LOAD VALUES FOR METRIC MJ EXTERNALLY THREADED FASTENERS |
| NAM 1312/105 : REV 1 | FASTENER TEST METHODS METRIC METHOD 105 STRESS DURABILITY |
| SAE AMS 2400 : 2013 | PLATING, CADMIUM |
| NAM 1312/108 : REV 1 | FASTENER TEST METHODS, METRIC METHOD 108 TENSILE STRENGTH |
| SAE AMS 6350 : 2015 | STEEL SHEET, STRIP, AND PLATE, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130) |
| SAE AMS 6370 : 2016 | STEEL, BARS, FORGINGS, AND RINGS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130) |
| NAM 1312/111 : REV 1 | FASTENER TEST METHODS, METRIC METHOD 111 TENSION FATIGUE |
| NAM 1312/107 : REV 1 | FASTENER TEST METHODS, METRIC METHOD 107 VIBRATION |
| SAE MA 3376 : 2012 | BOLTS & SCREWS, UNS G87400 TENSILE STRENGTH 860 MPA & 1000 MPA PROCUREMENT SPECIFICATION, METRIC |
| SAE AS 1310 : 2012 | FASTENER TORQUE FOR THREADED APPLICATIONS, DEFINITIONS OF |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.