SAE MAM6415C
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Steel, Bars, Forgings, and Tubing, 0.80cr 1.8ni 0.25mo (0.38 0.43)
Hardcopy , PDF
07-10-2019
English
12-03-2003
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1 Scope
2 Applicable documents
3 Technical requirements
4 Quality assurance provisions
5 Preparation for delivery
6 Acknowledgement
7 Rejections
8 Notes
Describes aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock procured in SI (Metric) units. Used typically for parts, 90 millimeters and under in nominal thickness at time of heat treatment.
| DocumentType |
Standard
|
| Pages |
9
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| Supersedes |
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock procured in SI (Metric) units. AMS 6415 is the inch/pound version of this MAM. These products have been used typically for parts, 90 millimeters and under in nominal thickness at time of heat treatment, requiring a through-hardening steel capable of developing a minimum hardness of 40 HRC when properly hardened and tempered and also for parts of greater thickness but requiring proportionately lower hardness, but usage is not limited to such applications. Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking after heat treatment; ARP 1110 recommends practices to minimize such conditions.
| Standards | Relationship |
| MIL-S-5000 Revision E:1982 | Similar to |
| SAE ARP1110C | Minimizing Stress Corrosion Cracking in Wrought Forms of Steels and Corrosion Resistant Steels and Alloys |
| SAE AMS2372G | Quality Assurance Sampling and Testing Carbon and Low-Alloy Steel Forgings |
| SAE AMS2370L | Quality Assurance Sampling and Testing Carbon and Low-Alloy Steel Wrought Products and Forging Stock |
| MIL-H-6875 Revision H:1989 | HEAT TREATMENT OF STEEL RAW MATERIALS |
| SAE AMS 2806D : 2013 | IDENTIFICATION BARS, WIRE, MECHANICAL TUBING, AND EXTRUSIONS, CARBON AND ALLOY STEELS AND CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS |
| SAE AS1182C | Standard Stock Removal Allowance Aircraft-Quality and Premium Aircraft-Quality Steel Bars and Mechanical Tubing |
| ASTM E 350 : 2012-09 | TEST METHODS FOR CHEMICAL ANALYSIS OF CARBON STEEL, LOW-ALLOY STEEL, SILICON ELECTRICAL STEEL, INGOT IRON, AND WROUGHT IRON |
| SAE MAM2251C | Tolerances, Metric, Low-Alloy Steel Bars |
| SAE MAM2301C | Steel Cleanliness, Aircraft Quality Magnetic Particle Inspection Procedure Metric (SI) Measurement |
| SAE MAM2253B | Tolerances, Metric, Carbon and Alloy Steel Tubing |
| ASTM E 381 : 2017 : REDLINE | Standard Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings |
| SAE AMS2808E | Identification Forgings |
| SAE AMS2259E | Chemical Check Analysis Limits Wrought Low-Alloy and Carbon Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.