SN EN ISO 10535 : 2007

Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 General requirements and test methods
    4.1 General requirements
          4.1.1 Risk analysis
          4.1.2 Ergonomics factors etc.
          4.1.3 Sound level
    4.2 General test conditions
          4.2.1 Test conditions
          4.2.2 Test equipment
          4.2.3 Tolerances
          4.2.4 Test report
    4.3 General safety requirements
    4.4 Test methods for general safety requirements
    4.5 Requirements for performance
    4.6 Test methods for performance
    4.7 Requirements for rate (velocity) of lifting and
          lowering
    4.8 Test methods for rate (velocity) of lifting and
          lowering
    4.9 Requirements for operating forces
    4.10 Test methods for operating forces
    4.11 Information supplied by the manufacturer
          4.11.1 General
          4.11.2 Marking
          4.11.3 Instructions for use
    4.12 Requirements for durability
    4.13 Test methods for durability
5 Mobile Hoists - Specific requirements and test methods
    5.1 Requirements for static strength
    5.2 Test methods for static strength
    5.3 Requirements for static stability
    5.4 Test methods for static stability
    5.5 Requirements for immobilizing device (brakes)
    5.6 Test methods for immobilizing device (brakes)
    5.7 Requirements for moving forces
    5.8 Test methods for moving forces
    5.9 Instructions for use
6 Stationary Hoists - Specific requirements and test methods
    6.1 Specific safety requirements
    6.2 Test methods for specific safety requirements
    6.3 Requirements for static strength for all stationary
          hoists
    6.4 Requirements for static strength (free standing
          hoists only)
    6.5 Test methods for static strength (free standing
          stationary hoists only)
    6.6 Requirements for static stability (free standing
          stationary hoists only)
    6.7 Test methods for static stability (free-standing
          stationary hoists only)
    6.8 Requirements for static strength for all other
          stationary hoists
    6.9 Test methods for static strength for all other
          stationary hoists
    6.10 Instructions for use
7 Non-rigid body support units - Specific requirements and
    test methods
    7.1 General
    7.2 Requirements for central suspension point
    7.3 Test method for central suspension point
    7.4 Requirements for the spreader bar
    7.5 Test methods for the spreader bar
    7.6 Requirements for the non-rigid body support unit
    7.7 Material and seams of the non-rigid body support
          unit
    7.8 Test methods for body support unit
    7.9 Marking
    7.10 Instructions for use
8 Rigid body support units - Specific requirements and
    test methods
    8.1 General
    8.2 Requirement for backrest
    8.3 Requirements and test methods for durability
    8.4 marking
    8.5 Instructions for use
9 Free-standing hoists for use in bath tubs
Figures
Annex A (informative) Periodic inspection
Annex B (informative) Applications
Annex C (normative) Hydraulic and pneumatic components-
                        requirements and test methods
Annex Z (informative) Clauses of this European Standard
                        addressing essential requirements or
                        other provisions of EU Directives

Defines requirements and test methods only for hoists and body-support units intended for the transfer of disabled persons as classified in ISO 9999:2002: - 12 36 03 Mobile hoists with sling seats; - 12 36 04 Standing mobile hoists; - 12 36 06 Mobile hoists with solid seats; - 12 36 09 Hoist trolleys; - 12 36 12 Stationary hoists fixed to the wall/walls, floor and/or ceiling; - 12 36 15 Stationary hoists fixed to, mounted in or on another product; - 12 36 18 Stationary free-standing hoists; - 12 36 21 Body-support units for hoists.