UNI EN 14765 : 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BICYCLES FOR YOUNG CHILDREN - SAFETY REQUIREMENTS AND TEST METHODS
04-10-2022
01-01-2008
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements and test methods
4.1 Brake tests and strength tests - special requirements
4.1.1 Definition of brake tests
4.1.2 Definition of strength tests
4.1.3 Numbers and condition of specimens for the
strength tests
4.1.4 Accuracy tolerances of test conditions for brake
tests and strength tests
4.2 Toxicity
4.3 Sharp edges
4.4 Security and strength of safety-related fasteners
4.4.1 Security of screws
4.4.2 Minimum failure torque
4.4.3 Quick-release devices
4.4.4 Foot location devices
4.5 Crack detection methods
4.6 Protrusions
4.6.1 Requirement
4.6.2 Test method
4.7 Brakes
4.7.1 Braking-systems
4.7.2 Hand-operated brakes
4.7.3 Attachment of brake assembly and cable requirements
4.7.4 Brake-block and brake-pad assemblies - security test
4.7.5 Brake adjustment
4.7.6 Back-pedal brake
4.7.7 Braking-system - strength tests
4.7.8 Braking performance
4.8 Steering
4.8.1 Handlebar - dimensions and end fittings
4.8.2 Handlebar grips
4.8.3 Handlebar-stem - insertion depth mark or positive stop
4.8.4 Steering stability
4.8.5 Steering assembly - static strength and security tests
4.8.6 Handlebar and stem assembly - fatigue test
4.9 Frames
4.9.1 Frame and front fork assembly - impact test (falling
mass)
4.9.2 Frame and front fork assembly - impact test (falling
frame)
4.10 Front fork
4.10.1 General
4.10.2 Front fork - bending fatigue test
4.11 Wheels
4.11.1 Rotational accuracy
4.11.2 Wheel/tyre assembly - clearance
4.11.3 Wheel/tyre assembly - static strength test
4.11.4 Wheel retention
4.12 Rims, tyres and tubes
4.12.1 Tyre inflation pressure
4.12.2 Tyre and rim compatibility
4.13 Pedals and pedal/crank drive system
4.13.1 Pedal tread
4.13.2 Pedal clearance
4.13.3 Pedal-spindle impact test
4.13.4 Pedal/pedal-spindle - dynamic durability test
4.13.5 Drive system static strength test
4.13.6 Crank assembly - fatigue tests
4.14 Saddles and seat-pillars
4.14.1 Limiting dimensions
4.14.2 Seat-pillar - insertion-depth mark or positive stop
4.14.3 Saddle and seat pillar - security test
4.14.4 Saddle - static strength test
4.14.5 Seat-pillar - fatigue test
4.15 Chain-guard
4.16 Stabilizers
4.16.1 Mounting and dismounting
4.16.2 Dimensions
4.16.3 Vertical load test
4.16.4 Longitudinal load test
4.17 Luggage carriers
4.18 Lighting systems and reflectors
4.18.1 Lighting and reflectors
4.18.2 Wiring harness
4.18.3 Warning device
5 Instructions
6 Marking
6.1 Requirement
6.2 Durability test
6.2.1 Requirement
6.2.2 Test method
Annex A (informative) - Steering geometry
Bibliography
Describes safety and performance requirements and test methods for bicycles for young children, in respect of the design, assembly and testing of bicycles and sub-assemblies.
DocumentType |
Standard
|
PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
UNE-EN 14765:2006 | Identical |
NBN EN 14765 : 2006 + A1 2008 | Identical |
SN EN 14765 : 2006 + A1 2008 | Identical |
NS EN 14765 : 2005 + A1 2008 | Identical |
I.S. EN 14765:2006 | Identical |
NF EN 14765 : 2006 + A1 2008 | Identical |
BS EN 14765 : 2005 | Identical |
EN 14765:2005+A1:2008 | Identical |
NEN EN 14765 : 2005 + A1 2008 | Identical |
DIN EN 14765:2008-06 | Identical |
ISO 7636:1984 | Bells for bicycles and mopeds Technical specifications |
ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
EN 14872:2006 | Bicycles - Accessories for bicycles - Luggage carriers |
ISO 5775-1:2014 | Bicycle tyres and rims — Part 1: Tyre designations and dimensions |
ISO 3452-3:2013 | Non-destructive testing — Penetrant testing — Part 3: Reference test blocks |
ISO 5775-2:2015 | Bicycle tyres and rims Part 2: Rims |
ISO 3452-2:2013 | Non-destructive testing Penetrant testing Part 2: Testing of penetrant materials |
ISO 3452-4:1998 | Non-destructive testing Penetrant testing Part 4: Equipment |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.