UNI EN ISO 15874-2 : 2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 2: PIPES
02-09-2022
01-01-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated terms
4 Material
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics
8 Physical and chemical characteristics
9 Performance requirements
10 Marking
Annex A (informative) - Derivation of S[calc,max]
Bibliography
Describes the requirements of pipes made from polypropylene (PP) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems under operating pressures and temperatures appropriate to the class of application.
| DevelopmentNote |
Supersedes UNI 8318. (08/2005)
|
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 15874-2:2013 | Identical |
| NF EN ISO 15874-2 : 2013 | Identical |
| NBN EN ISO 15874-2 : 2013 | Identical |
| NEN EN ISO 15874-2 : 2013 | Identical |
| NS EN ISO 15874-2 : 2013 | Identical |
| I.S. EN ISO 15874-2:2013 | Identical |
| SN EN ISO 15874-2:2013 | Identical |
| UNE-EN ISO 15874-2:2013 | Identical |
| BS EN ISO 15874-2 : 2013 | Identical |
| EN ISO 15874-2:2013 | Identical |
| DIN EN ISO 15874-2:2013-06 | Identical |
| ONORM EN ISO 15874-2 : 2013 | Identical |
| DIN EN ISO 15874-2:2004-03 | Identical |
| UNI 11397 : 2011 | WELDING - WELDING OF PLASTICS - WELDING OF POLYPROPYLENE COMPONENTS FOR PRESSURE FLUIDS TRANSMISSION - BUTT WELDING |
| UNI 11318 : 2009 | WELDING - WELDING OF PLASTICS - WELDING OF POLYPROPYLENE COMPONENTS FOR PRESSURE FLUIDS TRANSMISSION - SOCKET WELDING |
| ISO 15874-3:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 3: Fittings |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
| ISO 15874-1:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 1: General |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 9854-1:1994 | Thermoplastics pipes for the transport of fluids — Determination of pendulum impact strength by the Charpy method — Part 1: General test method |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| CEN/TR 12108:2012 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| ISO 9854-2:1994 | Thermoplastics pipes for the transport of fluids — Determination of pendulum impact strength by the Charpy method — Part 2: Test conditions for pipes of various materials |
| ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
| ISO 13760:1998 | Plastics pipes for the conveyance of fluids under pressure — Miner's rule — Calculation method for cumulative damage |
| ISO 15874-5:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 5: Fitness for purpose of the system |
| ISO/TS 15874-7:2003 | Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 7: Guidance for the assessment of conformity |
| ISO 7686:2005 | Plastics pipes and fittings — Determination of opacity |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
| ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.