UNI ISO 3951-1 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SAMPLING PROCEDURES FOR INSPECTION BY VARIABLES - PART 1: SPECIFICATION FOR SINGLE SAMPLING PLANS INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION FOR A SINGLE QUALITY CHARACTERISTIC AND A SINGLE AQL
23-11-2022
06-11-2014
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Acceptance quality limit (AQL)
6 Switching rules for normal, tightened, and
reduced inspection
7 Relation to ISO 2859-1
8 Consumer protection
9 Allowing for measurement uncertainty
10 Planning
11 Choice between variables and attributes
12 Choice between the s-method and sigma-method
13 Choice of inspection level and AQL
14 Choice of sampling scheme
15 Preliminary operations
16 Standard procedures for the s-method
17 Standard procedures for the sigma-method
18 Procedure during continuing inspection
19 Normality and outliers
20 Records
21 Operation of switching rules
22 Discontinuation and resumption of inspection
23 Switching between the s-method and sigma-method
24 Charts B to R - Operating characteristic curves
and tabulated values for single sampling plans,
normal inspection: s-method
25 Charts s-D to s-R - Acceptance curves for combined
control of double specification limits: s-method
Annex A (normative) - Table for determining the sample
size code letter
Annex B (normative) - Form k for single sampling plans:
s-method
Annex C (normative) - Form k for single sampling plans:
sigma-method
Annex D (normative) - Values of f[s] for maximum sample
standard deviation (MSSD)
Annex E (normative) - Values of f[sigma] for maximum
process standard deviation (MPSD)
Annex F (normative) - Estimating the process fraction
nonconforming for sample size 3: s-method
Annex G (normative) - Single sampling plans of Form p*
Annex H (normative) - Values of c[U] for upper control limit
on the sample standard deviation
Annex I (normative) - Supplementary acceptability constants
for qualifying towards reduced inspection
Annex J (normative) - Procedures for obtaining s and sigma
Annex K (informative) - Consumer's risk qualities
Annex L (informative) - Producer's risks
Annex M (informative) - Operating characteristics for the
sigma-method
Annex N (informative) - Estimating the process fraction
nonconforming for sample sizes 3 and 4: s-method
Annex O (normative) - Accommodating measurement variability
Bibliography
This part of ISO 3951 specifies an acceptance sampling system of single sampling plans for inspection by variables.
| Committee |
U27.00
|
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 3951-1:2013 | Identical |
| ISO 2854:1976 | Statistical interpretation of data — Techniques of estimation and tests relating to means and variances |
| ISO 16269-4:2010 | Statistical interpretation of data Part 4: Detection and treatment of outliers |
| ISO 7870:1993 | Control charts General guide and introduction |
| ISO 31-11:1992 | Quantities and units Part 11: Mathematical signs and symbols for use in the physical sciences and technology |
| ISO 10576-1:2003 | Statistical methods — Guidelines for the evaluation of conformity with specified requirements — Part 1: General principles |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| ISO 2859-0:1995 | Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system |
| ISO 3534-2:2006 | Statistics — Vocabulary and symbols — Part 2: Applied statistics |
| ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| ISO 5479:1997 | Statistical interpretation of data — Tests for departure from the normal distribution |
| ISO 3951-2:2013 | Sampling procedures for inspection by variables — Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics |
| ISO 3534-1:2006 | Statistics — Vocabulary and symbols — Part 1: General statistical terms and terms used in probability |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.