00/121221 DC : DRAFT MARCH 2000

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

ISO/CE 1133 - PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS

Available format(s):

Superseded date: 11-10-2005

Language(s):

Published date: 23-11-2012

Publisher: British Standards Institution

Table of Contents - (Show below) - (Hide below)

Foreword
1 Scope
2 Normative references
3 Apparatus
   3.1 Basis Apparatus
   3.2 Accessory Equipment
4 Test Sample
5 Temperature Calibration, cleaning and maintenance
   of the apparatus
   5.1 Calibration of the temperature-control system
   5.2 Cleaning the apparatus
6 Procedure A
7 Procedure B
   7.1 Principle
   7.2 Optimum measurement accuracy
   7.3 Pre-treatment
   7.4 Determination
   7.5 Expression of results
8 Flow rate ratio (FRR)
9 Precision
10 Test report
Annex A (informative) Test conditions for melt flow
        rate determination
Annex B (informative) Conditions in use for the
        designation of standards for thermoplastic
        materials

Abstract - (Show below) - (Hide below)

Draft: ISO/CD 1133

General Product Information - (Show below) - (Hide below)

Comment Closes On
Committee	PRI/21
Document Type	Draft
ISBN
Pages
Published
Publisher	British Standards Institution
Status	Superseded
Superseded By	BS EN ISO 1133:2005

Standards Referencing This Book - (Show below) - (Hide below)

ISO 6507-1:2005	Metallic materials Vickers hardness test Part 1: Test method
ISO 1622-1:2012	Plastics Polystyrene (PS) moulding and extrusion materials Part 1: Designation system and basis for specifications
ISO 1628-1:2009	Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 1: General principles
ISO 6402-1:2002	Plastics Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials Part 1: Designation system and basis for specifications
ISO 1873-2:2007	Plastics Polypropylene (PP) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ISO 4613-1:1993	Plastics Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials Part 1: Designation and specification
ISO 2897-1:1997	Plastics Impact-resistant polystyrene (PS-I) moulding and extrusion materials Part 1: Designation system and basis for specifications
ISO 4894-1:1997	Plastics Styrene/acrylonitrile (SAN) moulding and extrusion materials Part 1: Designation system and basis for specifications
ISO 9988-1:2004	Plastics Polyoxymethylene (POM) moulding and extrusion materials Part 1: Designation system and basis for specifications
ISO 8257-1:1998	Plastics Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Part 1: Designation system and basis for specifications
ISO 468:1982	Surface roughness — Parameters, their values and general rules for specifying requirements
ISO 7391-1:2006	Plastics Polycarbonate (PC) moulding and extrusion materials Part 1: Designation system and basis for specifications
ISO 1872-1:1993	Plastics Polyethylene (PE) moulding and extrusion materials Part 1: Designation system and basis for specifications
ISO 2580-1:2002	Plastics Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Part 1: Designation system and basis for specifications
ISO 10366-1:2002	Plastics Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials Part 1: Designation system and basis for specifications

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart