02/206403 DC : DRAFT MAY 2002

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

IEC 62231. ED.1.0 - COMPOSITE STATION POST INSULATORS FOR SUBSTATIONS WITH A.C. VOLTAGES GREATER THAN 1000 V UPTO 245 KV - DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA

Available format(s):

Superseded date: 31-05-2007

Language(s):

Published date: 23-11-2012

Publisher: British Standards Institution

Table of Contents - (Show below) - (Hide below)

FOREWORD
INTRODUCTION
SECTION ONE - GENERAL
1 Scope and object
2 Normative references
3 Definitions
4 Identification
SECTION TWO - TESTS
5 Classification of Tests
  5.1 Design tests
  5.2 Type tests
  5.3 Sample tests
  5.4 Routine tests
6 Design Tests
  6.1 General
  6.2 Tests on interfaces and connections of end
      fittings
  6.3 Assembled core load tests
  6.4 Tests of shed and housing material
  6.5 Tests for the core material
7 Type tests
  7.1 Verification of dimensions
  7.2 Electrical test
  7.3 Mechanical test
8 Sample tests
  8.1 General rule
  8.2 Verification of dimensions (E1 + E2)
  8.3 Galvanizing test (E1 + E2)
  8.4 Verification of the specified mechanical loads (E1)
  8.5 Re-testing procedure
9 Routine tests
  9.1 Identification of the station post insulator
  9.2 Visual examination
  9.3 Tension load test
Annex A (Informative) Determination of the equivalent
        bending moment caused by combined compression
        (tension) and cantilever loads
Annex B (Informative) Example of torsion test arrangement
Annex C (Normative) Tolerances of Form and Position
Annex D (Informative) Notes on the compression/buckling
        test

General Product Information - (Show below) - (Hide below)

Comment Closes On
Committee	PEL/36/3
Document Type	Draft
ISBN
Pages
Published
Publisher	British Standards Institution
Status	Superseded
Superseded By	BS EN 62231:2007

Standards Referencing This Book - (Show below) - (Hide below)

ISO 4892-1:2016	Plastics Methods of exposure to laboratory light sources Part 1: General guidance
IEC 61467:2008	Insulators for overhead lines - Insulator strings and sets for lines with a nominal voltage greater than 1 000 V - AC power arc tests
IEC 60050-471:2007	International Electrotechnical Vocabulary (IEV) - Part 471: Insulators
IEC 62217:2012	Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria
IEC 60383-1:1993	Insulators for overhead lines with a nominal voltage above 1000 V - Part 1: Ceramic or glass insulator units for a.c. systems - Definitions, test methods and acceptance criteria
IEC 61109:2008	Insulators for overhead lines - Composite suspension and tension insulators for a.c. systems with a nominal voltage greater than 1 000 V - Definitions, test methods and acceptance criteria
IEC 61952:2008	Insulators for overhead lines - Composite line post insulators for A.C. systems with a nominal voltage greater than 1 000 V - Definitions, test methods and acceptance criteria
IEC 60865-1:2011	Short-circuit currents - Calculation of effects - Part 1: Definitions and calculation methods
ISO 4892-3:2016	Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps
IEC 61462:2007	Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1 000 V - Definitions, test methods, acceptance criteria and design recommendations
ISO 468:1982	Surface roughness — Parameters, their values and general rules for specifying requirements
IEC 60695-11-10:2013	Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
ISO 4892-2:2013	Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
IEC 60060-1:2010	High-voltage test techniques - Part 1: General definitions and test requirements
IEC 60168:1994+AMD1:1997+AMD2:2000 CSV	Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1000 V
ISO 868:2003	Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart