EN ISO 3126:2005
|
Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
EN 682:2002/A1:2005
|
ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR SEALS USED IN PIPES AND FITTINGS CARRYING GAS AND HYDROCARBON FLUIDS |
EN 10226-2:2005
|
Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
ISO 13953:2001
|
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
ISO 1167-2:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
ISO 10838-3:2001
|
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm |
EN ISO 1167-2:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
ISO 10838-2:2000
|
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm |
PREN 1555-2 : DRAFT 2008
|
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
EN ISO 1167-1:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
ISO 10838-1:2000
|
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm |
ISO 1167-4:2007
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
IEC 60364-1:2005
|
Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions |
EN 1716:1997
|
Plastics piping systems - Polyethylene (PE) tapping tees - Test method for impact resistance of an assembled tapping tee |
PREN 1555-5 : DRAFT 2008
|
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM |
ISO 3126:2005
|
Plastics piping systems Plastics components Determination of dimensions |
ISO 11922-1:1997
|
Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
EN ISO 1167-4:2007
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007) |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV
|
Degrees of protection provided by enclosures (IP Code) |
ISO 1167-3:2007
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components |
ISO 13954:1997
|
Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
ISO 13955:1997
|
Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies |
EN 12007-2:2012
|
Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
CEN/TS 1555-7:2013
|
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
EN ISO 1133:2005
|
PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS |
EN 12117:1997
|
Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships |
EN 10226-1:2004
|
Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
PREN 1555-1 : DRAFT 2008
|
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
ISO 1133:2005
|
Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
ISO 228-1:2000
|
Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
EN ISO 1167-3:2007
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 3: Preparation of components (ISO 1167-3:2007) |
ISO 1167-1:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |