09/30195206 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 54-30 - FIRE DETECTION AND ALARM SYSTEMS - PART 30: MULTI-SENSOR FIRE DETECTORS - POINT DETECTORS USING A COMBINATION OF CARBON MONOXIDE AND HEAT SENSORS
Hardcopy , PDF
30-04-2015
English
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
4.1 Compliance
4.2 Individual alarm indication
4.3 Connection of ancillary devices
4.4 Monitoring of detachable detectors
4.5 Manufacturer's adjustments
4.6 On-site adjustment of response behaviour
4.7 Rate-sensitive CO response
4.8 Position of the heat sensors
4.9 Marking
4.10 Data
4.11 Additional requirements for software controlled
detectors
5 Test methods
5.1 General
5.2 Repeatability of CO response
5.3 Directional dependence of CO response
5.4 Directional dependence of heat response
5.5 Lower limit of heat response
5.6 Reproducibility of CO
5.7 Reproducibility of heat response
5.8 Long term stability (operational)
5.9 Variation in supply parameters
5.10 Air movement
5.11 Dry heat (operational)
5.12 Dry heat (endurance)
5.13 Cold (operational)
5.14 Damp heat, cyclic (operational)
5.15 Damp heat, steady state (operational)
5.16 Damp heat, steady state (endurance)
5.17 Low humidity, steady state (operational)
5.18 Sulphur dioxide SO[2] corrosion (endurance)
5.19 Shock (operational)
5.20 Impact (operational)
5.21 Vibration, sinusoidal (operational)
5.22 Vibration, sinusoidal (endurance)
5.23 Exposure to chemical agents at environmental
concentrations
5.24 Exposure to high level of carbon monoxide
5.25 Electromagnetic Compatibility (EMC), immunity tests
(operational)
5.26 Fire sensitivity
Annex A (normative) - Gas test chamber for CO response
threshold value and cross-sensitivity to chemical
agents
Annex B (normative) - Fire test room
Annex C (normative) - Measuring instruments for smoke and CO
C.1 General
C.2 CO measuring instrument
C.3 Obscuration meter
C.4 Measuring ionization chamber (MIC)
Annex D (informative) - Establishing exposure levels of
chemical agents
D.1 General
D.2 Establishing concentration of chemical agents for
test gases 1 to 9 of 5.23
D.3 Verification of test chamber leakage
D.4 Establishing concentration of ozone
Annex E (normative) - Heat tunnel for heat response value
Annex F (normative) - Smouldering (pyrolysis) wood fire (TF2)
F.1 General
F.2 Fuel
F.3 Hotplate
F.4 Arrangement
F.5 Heating rate
F.6 End-of-test condition
F.7 Test validity criteria
Annex G (normative) - Glowing smouldering cotton fire (TF3)
G.1 Introduction
G.2 Fuel
G.3 Arrangement
G.4 Ignition
G.5 End-of-test condition
G.6 Test validity criteria
Annex H (normative) - Open plastics (polyurethane) fire (TF4)
H.1 Introduction
H.2 Fuel
H.3 Conditioning
H.4 Arrangement
H.5 Ignition
H.6 Method of ignition
H.7 End-of-test condition
H.8 Test validity criteria
Annex I (normative) - Liquid (heptane) fire (TF5)
I.1 Introduction
I.2 Fuel
I.3 Arrangement
I.4 Ignition
I.5 End-of-test condition
I.6 Test validity criteria
Annex J (informative) - Information concerning the construction
of the gas test chamber
Annex K (informative) - Construction of the heat tunnel
Annex L (informative) - Apparatus for impact test
Annex ZA (informative) - Clauses of this European Standard
addressing the provisions of the EU Construction
Products Directive (89/106/EEC)
ZA.1 Scope and relevant clauses
ZA.2 Procedures for the attestation of conformity of
control and indicating equipment covered by this
standard
ZA.3 CE marking and labelling and accompanying
documentation
ZA.4 EC certificate of conformity and EC declaration of
conformity
BS EN 54-30
Committee |
FSH/12/2
|
DocumentType |
Draft
|
Pages |
70
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
PREN 54-30 : DRAFT 2009 | Identical |
EN 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
EN 60068-2-42:2003 | Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections |
EN 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
EN 54-5:2017 | Fire detection and fire alarm systems - Part 5: Heat detectors - Point heat detectors |
EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
EN 54-26:2015 | Fire detection and fire alarm systems - Part 26: Carbon monoxide detectors - Point detectors |
EN 60068-2-27:2009 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
ISO 9001:2015 | Quality management systems — Requirements |
EN 60068-2-78:2013 | Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state |
EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
EN 50130-4:2011/A1:2014 | ALARM SYSTEMS - PART 4: ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD: IMMUNITY REQUIREMENTS FOR COMPONENTS OF FIRE, INTRUDER, HOLD UP, CCTV, ACCESS CONTROL AND SOCIAL ALARM SYSTEMS |
EN 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
EN 54-1:2011 | Fire detection and fire alarm systems - Part 1: Introduction |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.