10/30228356 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN ISO 15874-3 - PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 3: FITTINGS
Hardcopy , PDF
English
31-03-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and
abbreviated terms
4 Material characteristics
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics of plastics fittings
8 Physical and chemical characteristics of plastics
components
9 Sealing elements
10 Performance requirements
11 Marking
Bibliography
BS EN ISO 15874-3
| Committee |
PRI/88/2
|
| DocumentType |
Draft
|
| Pages |
26
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN ISO 15874-3 : DRAFT 2010 | Identical |
| EN 1254-3:1998 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 15874-1:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 1: General |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 15874-2:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 2: Pipes |
| ISO 12092:2000 | Fittings, valves and other piping system components made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) for pipes under pressure — Resistance to internal pressure — Test method |
| ISO 3126:2005 | Plastics piping systems — Plastics components — Determination of dimensions |
| ENV 12108:2001 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| ISO 15874-5:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 5: Fitness for purpose of the system |
| ISO/TS 15874-7:2003 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 7: Guidance for the assessment of conformity |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| EN 12107 : 1997 | PLASTICS PIPING SYSTEM - INJECTION MOULDED THERMOPLASTICS FITTINGS, VALVES AND ANCILLARY EQUIPMENT - DETERMINATION OF THE LONG-TERM HYDROSTATIC STRENGTH OF THERMOPLASTICS MATERIALS FOR INJECTION MOULDING OF PIPING COMPONENTS |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation |
| ISO 7686:2005 | Plastics pipes and fittings — Determination of opacity |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.