Skip to content
Please enter a keyword to search

  • 13/30280432 DC : 0

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    BS ISO 16422 - PIPES AND JOINTS MADE OF ORIENTED UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-O) FOR THE CONVEYANCE OF WATER UNDER PRESSURE - SPECIFICATIONS

    Available format(s):  Hardcopy, PDF

    Superseded date:  28-02-2014

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Material
    6 Effect of materials on water quality
    7 Material classification
    8 Classification and selection of pipes
    9 General requirements for pipes
    10 Geometrical characteristics for pipes
    11 Mechanical characteristics of pipes
    12 Physical characteristics
    13 Mechanical characteristics of assemblies, including
       joints
    14 Elastomeric seals
    15 Marking
    Annex A (normative) - Establishment of the pipe material
            classification
    Annex B (informative) - Minimum depth of engagement
            of sockets
    Annex C (normative) - Temperature derating factor
    Annex D (informative) - Ring stiffness of pipes
    Annex E (informative) - Determination of the long-term
            test pressure by creep consideration
    Annex F (informative) - Determination of axial and
            tangential orientation factor

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee PRI/88/2
    Document Type Draft
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 2507-2:1995 Thermoplastics pipes and fittings — Vicat softening temperature — Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly (vinyl chloride) (PVC-HI) pipes
    ISO 6259-2:1997 Thermoplastics pipes Determination of tensile properties Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride) (PVC-HI)
    ISO 13846:2000 Plastics piping systems End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping Test method for long-term leaktightness under internal water pressure
    ISO 2507-1:1995 Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method
    ISO 3127:1994 Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method
    ISO 161-1:1996 Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series
    ISO 9080:2012 Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
    ISO 3:1973 Preferred numbers Series of preferred numbers
    ISO 1452-5:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 5: Fitness for purpose of the system
    ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
    ISO 13783:1997 Plastics piping systems — Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints — Test method for leaktightness and strength while subjected to bending and internal pressure
    ISO 13844:2015 Plastics piping systems Elastomeric-sealing-ring-type socket joints for use with plastic pressure pipes Test method for leaktightness under negative pressure, angular deflection and deformation
    ISO 1452-2:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 2: Pipes
    ISO 18373-1:2007 Rigid PVC pipes Differential scanning calorimetry (DSC) method Part 1: Measurement of the processing temperature
    ISO 1628-2:1998 Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 2: Poly(vinyl chloride) resins
    ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
    ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
    ISO 2531:2009 Ductile iron pipes, fittings, accessories and their joints for water applications
    ISO 4633:2015 Rubber seals — Joint rings for water supply, drainage and sewerage pipelines — Specification for materials
    ISO 9852:2007 Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified temperature (DCMT) — Test method
    ISO 7686:2005 Plastics pipes and fittings — Determination of opacity
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    ISO 2505:2005 Thermoplastics pipes — Longitudinal reversion — Test method and parameters
    ISO 13845:2015 Plastics piping systems Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes Test method for leaktightness under internal pressure and with angular deflection
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective