14/30268531 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN ISO 6892-1 - METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT ROOM TEMPERATURE
Hardcopy , PDF
31-07-2016
English
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Terms and symbols
5 Principle
6 Test piece
7 Determination of original cross-sectional area
8 Marking the original gauge length
9 Accuracy of testing apparatus
10 Conditions of testing
11 Determination of the upper yield strength
12 Determination of the lower yield strength
13 Determination of proof strength, plastic extension
14 Determination of proof strength, total extension
15 Method of verification of permanent set strength
16 Determination of the percentage yield point extension
17 Determination of the percentage plastic extension at
maximum force
18 Determination of the percentage total extension at
maximum force
19 Determination of the percentage total extension at fracture
20 Determination of percentage elongation after fracture
21 Determination of percentage reduction of area
22 Test report
23 Measurement uncertainty
Annex A (informative) - Recommendations concerning the use
of computer-controlled tensile testing machines
Annex B (normative) - Types of test pieces to be used for thin
products: sheets, strips and flats between 0,1 mm
and 3 mm thick
Annex C (normative) - Types of test pieces to be used for wire,
bars and sections with a diameter or thickness of less
than 4 mm
Annex D (normative) - Types of test pieces to be used for sheets
and flats of thickness equal to or greater than 3 mm,
and wire, bars and sections of diameter or thickness
equal to or greater than 4 mm
Annex E (normative) - Types of test pieces to be used for tubes
Annex F (informative) - Estimation of the crosshead separation
rate in consideration of the stiffness (or compliance) of the
testing equipment
Annex G (normative) - Determination of the modulus of elasticity
on metallic materials under uniaxial tensile loading
Annex H (informative) - Measuring the percentage elongation after
fracture if the specified value is less than 5%
Annex I (informative) - Measurement of percentage elongation
after fracture based on subdivision of the original gauge length
Annex J (informative) - Determination of the percentage plastic
elongation without necking, A[wn], for long products such as
bars, wire and rods
Annex K (informative) - Estimation of the uncertainty of measurement
Annex L (informative) - Precision of tensile testing - Results from
interlaboratory programmes
Bibliography
BS EN ISO 6892-1.
| Committee |
ISE/101/1
|
| DocumentType |
Draft
|
| Pages |
90
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| SEP 1235 : 2012 | BESTIMMUNG DES ELASTIZITAETSMODULS AN STAHL IM ZUGVERSUCH BEI RAUMTEMPERATUR |
| ISO/TTA 2:1997 | Tensile tests for discontinuously reinforced metal matrix composites at ambient temperatures |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| ISO 2566-2:1984 | Steel Conversion of elongation values Part 2: Austenitic steels |
| ISO 3183:2012 | Petroleum and natural gas industries Steel pipe for pipeline transportation systems |
| ISO 9513:2012 | Metallic materials — Calibration of extensometer systems used in uniaxial testing |
| ISO/TR 25679:2005 | Mechanical testing of metals Symbols and definitions in published standards |
| ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
| ASTM E 111 : 2017 : REDLINE | Standard Test Method for Young’s Modulus, Tangent Modulus, and Chord Modulus |
| ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
| SAC GB/T 228 : 2002 | METALLIC MATERIALS - TENSILE TESTING AT AMBIENT TEMPERATURE |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
| EN 10291 : 2000 | METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST |
| ISO 11960:2014 | Petroleum and natural gas industries Steel pipes for use as casing or tubing for wells |
| ISO/IEC Guide 98-3:2008 | Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.