Skip to content
Please enter a keyword to search

  • 15/30319712 DC : 0

    NA Status of Standard is Unknown

    BS EN 1279-4 - GLASS IN BUILDING - INSULATING GLASS UNITS - PART 4: METHODS OF TEST FOR THE PHYSICAL ATTRIBUTES OF EDGE SEAL COMPONENTS AND INSERTS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols, units, abbreviated terms and indexes
    5 Requirements for sealants
    6 Requirements for desiccants in bulk
    7 Requirements for polymeric matrix incorporating desiccant
    8 Requirements for inserts and spacers containing polymer
      materials
    Annex A (normative) - Adhesion test for outer sealants and metal
            edge seals
    Annex B (normative) - Adhesion on coatings and interlayer
            adhesion of coatings
    Annex C (normative) - Fogging test
    Annex D (normative) - Methods of water vapour transmission rate
            and gas permeation rate determination
    Annex E (normative) - Test methods for desiccants in bulk
    Annex F (normative) - Karl Fischer method for determination of
            T[i], T[f] and T[c]
    Annex G (normative) - Gravimetric method for determination of
            T[i], T[f] and T[c]
    Annex H (informative) - Volatile content test
    Annex I (informative) - Example of a sun simulating radiation source
    Annex J (informative) - Sealant sheet preparation for WVTR and
            GPR measurements
    Bibliography

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee B/520/2
    Document Type Draft
    Publisher British Standards Institution
    Status NA

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 13022-1:2014 Glass in building - Structural sealant glazing - Part 1: Glass products for structural sealant glazing systems for supported and unsupported monolithic and multiple glazing
    EN ISO 11358-1:2014 Plastics - Thermogravimetry (TG) of polymers - Part 1: General principles (ISO 11358-1:2014)
    PREN 1279-1 : DRAFT 95 GLASS IN BUILDING - INSULATING GLASS UNITS - PART 1: GENERALITIES AND DIMENSIONAL TOLERANCES
    EN 410:2011 Glass in building - Determination of luminous and solar characteristics of glazing
    ISO 9060:1990 Solar energy Specification and classification of instruments for measuring hemispherical solar and direct solar radiation
    PREN 1279-3 : DRAFT 2015 GLASS IN BUILDING - INSULATING GLASS UNITS - PART 3: LONG TERM TEST METHOD AND REQUIREMENTS FOR GAS LEAKAGE RATE AND FOR GAS CONCENTRATION TOLERANCES
    PREN 1279-2 : DRAFT 2015 GLASS IN BUILDING - INSULATING GLASS UNITS - PART 2: LONG TERM TEST METHOD AND REQUIREMENTS FOR MOISTURE PENETRATION
    EN 15434:2006+A1:2010 Glass in building - Product standard for structural and/or ultra-violet resistant sealant (for use with structural sealant glazing and/or insulating glass units with exposed seals)
    ISO 11600:2002 Building construction Jointing products Classification and requirements for sealants
    ISO 10563:2017 Buildings and civil engineering works — Sealants — Determination of change in mass and volume
    ISO 2528:2017 Sheet materials — Determination of water vapour transmission rate (WVTR) — Gravimetric (dish) method
    PREN 1279-6 : DRAFT 2015 GLASS IN BUILDING - INSULATING GLASS UNITS - PART 6: FACTORY PRODUCTION CONTROL AND PERIODIC TESTS
    ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
    ISO 11358-1:2014 Plastics Thermogravimetry (TG) of polymers Part 1: General principles
    ISO 5893:2002 Rubber and plastics test equipment Tensile, flexural and compression types (constant rate of traverse) Specification
    ISO 7500-1:2015 Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system
    EN ISO 10563:2017 Buildings and civil engineering works - Sealants - Determination of change in mass and volume (ISO 10563:2017)
    ISO 760:1978 Determination of water Karl Fischer method (General method)
    EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective