96/706683 DC : MAY 96
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
ISO 13707 RECIPROCATING COMPRESSORS FOR THE PETROLEUM AND GAS INDUSTRIES
23-07-2013
23-11-2012
0 INTRODUCTION
SECTION 1 - GENERAL
1.1 Scope
1.2 Alternative Designs
1.3 Conflicting Requirements
1.4 Definition of Terms
1.5 Normative References
SECTION 2 - BASIC DESIGN
2.1 General
2.2 Allowable Speeds
2.3 Allowable Discharge Temperature
2.4 Rod and Gas Loads
2.5 Critical Speeds
2.6 Compressor Cylinders
2.7 Valves and Unloaders
2.8 Pistons, Piston Rods and Piston Rings
2.9 Crankcases, Crankshafts, connecting Rods, Bearings
and Crossheads
2.10 Distance Pieces
2.11 Packing Cases and Pressure Packing
2.12 Compressor Frame Lubrication
2.13 Cylinder and Packing Lubrication
2.14 Materials
2.15 Nameplates and Rotation Arrows
SECTION 3 - ACCESSORIES
3.1 Drivers
3.2 Couplings and Guards
3.3 Reduction Gears
3.4 Belt drives
3.5 Mounting Plates
3.6 Controls and Instrumentation
3.7 Piping and Appurtenances
3.8 Intercoolers and Aftercoolers
3.9 Pulsation and Vibration Control Requirements
3.10 Air Intake Filters
3.11 Special Tools
SECTION 4 - INSPECTION, TESTING AND PREPARATION FOR SHIPMENT
4.1 General
4.2 Inspection
4.3 Testing
4.4 Preparation for Shipment
SECTION 5 - VENDOR'S DATA
5.1 General
5.2 Proposals
5.3 Contract Data
APPENDICES
A
A.1 Typical Data Sheets
A.2 Purchaser's Checklist
B Required Capacity, Manufacturer's Rated Capacity and
and no Negative Tolerance
C Piston Rod Runout
D Repairs to Grey or Nodular Iron Castings
E Examples of Typical Logic Diagram Showing Critical
Functions
F Vendor Drawing and Data Requirements
G Figures and Schematics
H Materials for Major Component Parts
I Distance Piece Vent, Drain and Buffer Systems to
Minimise Process Gas Leakage
J Reciprocating Compressor Nomenclature
K Inspector's Checklist
L Typical Mounting Plate Arrangement
M Pulsation and Vibration Control Studies
N Guideline for Compressor Gas Piping Design and
Preparation for an Acoustic Simulation Analysis
O Guidelines for Sizing Low Pass Acoustic Filters
P Compressor Components - Compliance with NACE MR 0175
Q Alarm and Shutdown Systems
Tables
1 Driver Trip Speeds
2 Maximum Allowable Working Pressure for Cylinder Materials
3 Relief Valve Settings
4 Minimum Alarm and Shutdown Requirements
5 Minimum Requirements for Piping Materials
6A Minimum Tubing Wall Thickness
6B Minimum Pipe Wall Thickness
7 ASTM Piping Material Standards
8 Maximum Severity of Defects in Castings
Describes minimum requirements for reciprocating compressors with their drivers, used in the petroleum and natural gas industries, with either lubricated or non-lubricated cylinders. (ISO/DIS 13707)
Committee |
MCE/8
|
DevelopmentNote |
PROJECT NO. 93 416
|
DocumentType |
Draft
|
PublisherName |
British Standards Institution
|
Status |
Withdrawn
|
API 661 : 2015 | PETROLEUM, PETROCHEMICAL, AND NATURAL GAS INDUSTRIES - AIR-COOLED HEAT EXCHANGERS |
ASTM A 181/A181M : 2014 : REDLINE | Standard Specification for Carbon Steel Forgings, for General-Purpose Piping |
ISO 1217:2009 | Displacement compressors Acceptance tests |
ISO 281-1:1977 | Rolling bearings Dynamic load ratings and rating life Part 1: Calculation methods |
NACE MR 01 75 : 2003 | METALS FOR SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING RESISTANCE IN SOUR OILFIELD ENVIRONMENTS |
ASTM A 420/A420M : 2016 : REDLINE | Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service |
API 670 : 2014 | MACHINERY PROTECTION SYSTEMS |
ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
API 660 : 2015 | SHELL-AND-TUBE HEAT EXCHANGERS |
IEC 60848:2013 | GRAFCET specification language for sequential function charts |
API 526 : 2017 | FLANGED STEEL PRESSURE-RELIEF VALVES |
ASTM A 105/A105M : 2014-11 | SPECIFICATION FOR CARBON STEEL FORGINGS FOR PIPING APPLICATIONS |
ASTM E 125 : 1963 : R2003 | Standard Reference Photographs for Magnetic Particle Indications on Ferrous Castings |
ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
ASTM A 312/A312M : 2017-03 | SPECIFICATION FOR SEAMLESS, WELDED, AND HEAVILY COLD WORKED AUSTENITIC STAINLESS STEEL PIPES |
ISO 3448:1992 | Industrial liquid lubricants — ISO viscosity classification |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.