98/230636 DC : DRAFT MARCH 98
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
DRAFT IEC 61010-2-031 - SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT CONTROL AND LABORATORY USE 2-031: SAFETY REQUIREMENTS FOR HAND-HELD PROBE ASSEMBLIES FOR ELECTRICAL MEASUREMENT TEST
15-03-2002
23-11-2012
1 Scope and object
1.1 Scope
1.2 Object
1.3 Verification
1.4 Environmental conditions
2 Normative references
3 Definitions
3.1 Parts and accessories
3.2 Electrical quantities
3.3 Tests
3.4 Safety terms
3.5 Insulation
3.6 Insulation co-ordination
3.7 Mains
4 Tests
4.1 General
4.2 Sequence of tests
4.3 Reference test conditions
4.4 Testing in single fault condition
5 Marking and documentation
5.1 Marking
5.2 Warning markings
5.3 Durability of marking
5.4 Documentation
6 Protection against electric shock
6.1 General
6.2 Determination of ACCESSIBLE parts
6.3 Permissible limits for ACCESSIBLE parts
6.4 Insulation requirements for protection against
electric shock
6.5 Clearances and creepage distances
6.6 Dielectric Strength tests
6.7 Constructional requirements for protection against
electric shock
7 Protection against mechanical hazards
8 Mechanical resistance to shock and impact
8.1 Rigidity Test
8.2 Drop Test
8.3 Impact swing test
9 Temperature limits and protection against the spread of fire
9.1 General
10 Resistance to heat
10.1 Integrity of clearances and creepage distances
10.2 Resistance to heat of probe assemblies
11 Protection against hazards from fluids
11.1 General
11.2 Cleaning
11.3 Special protected probe assemblies
12 Protection against explosion
12.1 Arc explosion
13 Components
13.1 General
13.2 Fuses
13.3 High integrity components
Annexes
A (normative) Measuring circuits for ACCESSIBLE current (see 6.3)
B (normative) Standard test fingers (see 6.2)
C (normative) Measurement of CREEPAGE DISTANCES and CLEARANCES
Committee |
EPL/66
|
DocumentType |
Draft
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy |
IEC 60060-2:2010 | High-voltage test techniques - Part 2: Measuring systems |
IEC 60050-351:2013 | International Electrotechnical Vocabulary (IEV) - Part 351: Control technology |
IEC 60051-6:1984 | Direct acting indicating analogue electrical measuring instruments and their accessories. Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters |
IEC 60051-1:2016 | Direct acting indicating analogue electrical measuring instruments and their accessories - Part 1: Definitions and general requirements common to all parts |
IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
IEC 60051-7:1984 | Direct acting indicating analogue electrical measuring instruments and their accessories. Part 7: Special requirements for multi-function instruments |
IEC 60051-4:1984 | Direct acting indicating analogue electrical measuring instruments and their accessories. Part 4: Special requirements for frequency meters |
IEC 60051-8:1984 | Direct acting indicating analogue electrical measuring instruments and their accessories. Part 8: Special requirements for accessories |
IEC 60051-9:1988 | Direct acting indicating analogue electrical measuring instruments and their accessories. Part 9: Recommended test methods |
IEC 60027-1:1992 | Letters symbols to be used in electrical technology - Part 1: General |
IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
IEC 60051-2:1984 | Direct acting indicating analogue electrical measuring instruments and their accessories. Part 2: Special requirements for ammeters and voltmeters |
IEC 60027-3:2002 | Letter symbols to be used in electrical technology - Part 3: Logarithmic and related quantities, and their units |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
IEC 60051-5:1985 | Direct acting indicating analogue electrical measuring instruments and their accessories. Part 5: Special requirements for phase meters, power factor meters and synchroscopes |
IEC 60359:2001 | Electrical and electronic measurement equipment - Expression of performance |
IEC 60664-3:2016 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
IEC 60027-2:2005 | Letter symbols to be used in electrical technology - Part 2: Telecommunications and electronics |
IEC 60027-4:2006 | Letter symbols to be used in electrical technology - Part 4: Rotating electric machines |
IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
IEC 61032:1997 | Protection of persons and equipment by enclosures - Probes for verification |
IEC 60027-2B:1980 | Letter symbols to be used in electrical technology - Part 2: Telecommunications and electronics |
ISO 3864:1984 | Safety colours and safety signs |
IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
IEC 60027-2A:1975 | Letter symbols to be used in electrical technology - Part 2: Telecommunications and electronics - First supplement |
IEC 60990:2016 | Methods of measurement of touch current and protective conductor current |
IEC 60617-2:1996 | Graphical symbols for diagrams - Partie 2: Symbol elements, qualifying symbols and other symbols having general application |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.